It should be noted that the following parts of the PrimeTest 200 are user
serviceable and must be replaced with appropriate parts as detailed below:
-
1 off fuse, nominal current rating 0.5 A, 600 V AC/DC, Quick Blow,
Type F (27B098)
-
2 off fuse, nominal current rating 10 A, 250 V AC/DC, Anti Surge,
Type T (27B106)
-
6 off Alkaline batteries, 1.5 V AA size.
Do not open unit, no other serviceable parts.
4.0
Description
The display and selectable functions of the PrimeTest 200 are specified below
in conjunction with Figure 1 and Figure 2.
4.1
Rotary Switch
1)
Test function is the PrimeTest 200 power off position.
2)
Test function selects the Class I safety test (earth continuity,
insulation resistance) test.
3)
Test function selects the differential leakage current test for Class I
equipment. Requires mains from power cord.
4)
Test function RCD selects the RCD test, and also indicates loop
resistance Requires mains from power cord.
5)
Test function IEC selects the IEC lead (earth continuity, insulation
resistance, wire check) test.
6)
Test function selects the Class II safety test (insulation resistance).
7)
Test function selects the touch current test for Class II equipment.
Requires mains from power cord.
8)
Measuring function selects the Lo ohms (up to 20 K
Ω
) resistance
measurement.
9)
Measuring function M
Ω
selects the insulation ( up to 200 M
Ω
) resistance
measurement.
10)
Measuring function selects the voltage (up to 250 V AC/DC)
measurement.
11)
Measuring function °C selects the temperature ( up to 400°C)
measurement.
4.2
LCD and Keymat
1)
Digital display for all measurement readings and polarity indication.
2)
Analogue bargraph display.
3)
Small digital display used to indicate Pass/Fail criteria or secondary test
requirements for selectable test functions e.g. Polarity.
4)
Battery indicator - symbol is illuminated depending on battery health
status (see section 5.6).
5)
button, enables or disables the audio buzzer. When selected the
symbol is illuminated on the LCD display. The audible alarm is activated
under the following conditions:-
-
<10
Ω
on test function.
-
Zeroing of the test leads.
-
When more than 30 V AC/DC is detected at test lead inputs
(see section 8 for affected test functions).
6)
button, enables or disables the lock function and allows test
parameters for M
Ω
and to be continuously applied (see section 5.4).
When selected the symbol is illuminated on the LCD display.
7)
button compensates for the test lead resistance in test
function. When selected the symbol is illuminated on the
LCD display.
8)
button, switches the display illumination on or off.
9)
button is used to start tests and activate the M
Ω
and measuring
functions.
10)
Rotary switch selects the required test function (see section 4.1).
11)
Equipment under test (EUT) socket.
12)
Negative (black) socket.
13)
Positive (red ) socket.
14)
IEC mains input socket.
PrimeTest 200
Operating Instructions
3
Summary of Contents for PrimeTest 200
