Sebart Professional KatanaS 30E Assembly Manual Download

Page: 2 / 19

Table of contents

Table of contents...............................................................................................................……….. 2

Required radio and motor..........................................................................................................…. 3

Additional required items, tools and adhesives.............................................................................. 3

Warning.......................................................................................................................................... 3

Before starting assembly ...........................................................................................................… 3

Using the manual........................................................................................................................... 3

Warranty information…................................................................................................................. 4

Section 1 – wing fillet installation….............................................................................................. 5

Section 2 – ailerons installation...................................................................................................... 6

Section 3 – aileron servo & control horn installation…............................................................…. 7

Section 4 – rudder installation….................................................................................................... 9

Section 5 – elevator installation ………..…................................................................................... 10

Section 6 – tail wheel installation…...………................................................................................ 12

Section 7 – elevator / rudder servo & control horn installation………………………………….. 13

Section 8 – landing gear & wheels installation………………….................................................. 14

Section 9 – electric motor installation……...................……......................................................... 15

Section 10 – cowl installation……........................................................................................……. 16

Section 11 – final radio installation …………................................................................................18

Section 12 – wings installation........................................................................................................ 18

Control throws................................................................................................................................ 18

Rates and expos..........................................................................................................................…. 19

Recommended CG......................................................................................................................…. 19

Range test your radio..................................................................................................................…. 19

Summary of Contents for Professional KatanaS 30E




















Search results

Summary of Contents for Professional KatanaS 30E

Reviews:

Related manuals for Professional KatanaS 30E

Brands by name

Popular brands

Sebart Professional KatanaS 30E, Assembly Manual

Search results

Summary of Contents for Professional KatanaS 30E

Reviews:

Related manuals for Professional KatanaS 30E

Brands by name

Popular brands