Seeburg 01095/dp User Manual Download

Page: 14 / 15

X6 dp

7 Declaration of conformity

Declaration of conformity

EG Declaration of conformity

This product

confirms to the following EU guidelines, including any additions:



2006/95/EG, Low Voltage



2004/108/EG, Electromagnetic Compatibility



(Locations: Appendix 1, Paragraph 1, a and b)

The following standards have been applied:



DIN EN 60065



DIN EN 55103-1:1996, classes E1 to E4



DIN EN 55103-2:1996, classes E1 to E4

Declared by: Winfried Seeburg, SEEBURG acoustic line GmbH

Place and date: Senden, 01.10.2019

Legally binding sign: ____________________________________________

The attachments constitute part of this declaration. This declaration certifies conformity with the

listed guidelines, but does not guarantee any product characteristics. The safety precautions listed

in the product documentation must be observed.

SEEBURG acoustic line Produktions- und Vertriebsgesellschaft mbH

Auweg 32

89231 Senden

07307 / 9700

– 0

Summary of Contents for 01095/dp
















Search results

Summary of Contents for 01095/dp

Reviews:

Related manuals for 01095/dp

Brands by name

Popular brands

Seeburg 01095/dp, User Manual

Search results

Summary of Contents for 01095/dp

Reviews:

Related manuals for 01095/dp

Brands by name

Popular brands