background image

G Sub 1501 dp 

5 Operation 

13 

 

 

 

 

 

 

 

 

 

 

 

Installation using three subwoofers (recommended): 

The performance of the cardioid configuration is better when 3 subwoofers are used together. The 

units can be stacked on top of each other or laid side by side on the ground. If in a stack, the low-

est unit should face the rear. If laid side by side, the middle unit faces the rear. 

As  in  the  previous  example  with  two  subwoofers,  the  rearwards  facing  subwoofer  is  operated  in 

Cardioid  Mode.  The  two  forwards  facing  units  are  operated  as  normal  without the  Cardioid  Mode 

activated  (e.g.  one  G  Sub  1501  dp+  with  a  passive  G  Sub  1501  connected  to  the  parallel  output 

SpeakON (4)  and  the  Cardioid  Mode  not  selected).  All  of  the  subwoofers  in  the  configuration 

should be operating at the same level and with the same cut-off frequency to get the best result.

 

Note: 

Both  subwoofers  must  be  set  to  the  same  cut-off  frequency.  The  cardioid  preset  of  rear-facing 

subwoofer must be activated. 

Application example: 

Only  the  rear-facing  subwoofer  is  operated  in  Cardioid  Mode.  This  applies  regardless  of  whether 

the two units are stacked on top of each other or laid side by side on the ground. 

 

 

G Sub 1501 dp 

120 Hz, Cardioid Mode, 0 dB 

e.g. G Sub 1501 dp or dp+ 

120 Hz, not in Cardioid Mode, 0 dB 

 

e.g. G Sub 1501 

passive connected 

Summary of Contents for G Sub 1501 dp

















Reviews: