Seeburg G Sub 1501 dp User Manual Download

Page: 14 / 16

G Sub 1501 dp

6 Technical specifications

Technical specifications

Speaker Components

15" Nd

Description

Digitally Powered Bass Extension

Amp Power

1500 W AES (single Mode) / 110-230 V

2400 W AES (dual Mode) / 110-230 V

Rated Current

3,8 A @ 230 V

SPL

(Peak @ 1m)

135 dB

Max. Input Signal

25 dBu

DSP

HDLM FPGA Processing 32 bit floating point

AD / DA

24 bit / 96 kHz

Latency

0,8 ms (analog in to analog out)

Usable Range

(-6dB)

35 Hz - 100 / 120 / 140 Hz

Tuning Frequency

Excursion minimum

42 Hz

Connectors

Neutrik XLR in/out

Neutrik PowerCon in/out
Neutrik Speakon NL4MP out

Handles

2 x

Rigging / Fittings

M20 on top
Wheelboard fittings

Weight

29,0 kg
(+ 6,0 kg wheelboard)

Size

height x width x depth

40,0 x 60,0 x 60,0

Order No.

00620/dp

The technical data sheet and further information about possible applications for the system and

available accessories can be downloaded at the following Internet address:

http://www.seeburg.net/download_getfile.php?file=downloads/06-Datenblaetter/G-Subwoofer/G-

Sub-1501-dp_Datenblatt_dt.pdf

This manual applies only to systems fitted with the

DPLM

-DSP Con-

troller.

The version fitted with the

DPLM

-DSP Controller can be identified by

the control panel located above the XLR connectors.

Summary of Contents for G Sub 1501 dp

















Search results

Summary of Contents for G Sub 1501 dp

Reviews:

Related manuals for G Sub 1501 dp

Brands by name

Popular brands

Seeburg G Sub 1501 dp, User Manual

Search results

Summary of Contents for G Sub 1501 dp

Reviews:

Related manuals for G Sub 1501 dp

Brands by name

Popular brands