background image

                                                                                                            

                                                                                                             SEEBURG acoustic line

 

 

 

 

 

3. Galeo Sub und Galeo stacked 

 

For groundstack operation of Galeo on top of Galeo Sub no frame is required.  

The  Galeo  units  are  mounted  directly  onto  the  stacking  device  of  the  Galeo 

Sub and the front spacer. This device offers a wide angular adjustment range 

so  that  the  lowermost  unit  can  also  be  inclined  downwards  on  high 

groundstacks.  

 

Observe  the  maximum  stacking  height  for  open-air  events  (danger  in  strong 

winds) and secure the entire stack in such a way as to exclude the possibility of 

toppling or movement.  

 

 

 

 

 

 

For inclination angles ranging from 3.5° to – 3.5° the stacking device rests on 

the upper steel plate and is secured using the ball lock pin.  

 

 

 

 

 

In the case of larger inclination angles ranging from -6° bis -12° the spacer of 

the  Galeo is  inserted  into  the  stacking  device  and  secured  using  the  ball lock 

pin.  

Alternatively, the Galeo flying frame can be extended into a stacking frame, so 

that  it  is  also  possible  to  stack  the  Galeo  without  the  Galeo  Sub.  This  set-up 

can then be mounted on TSE infra bass extensions placed horizontally on the 

floor.  

 

 

 

 

For  smaller  sound  applications  a  speaker  pole  can  be  screwed  into  the  M20 

thread  of  the  Galeo  Sub.  The  flying  shackle  Art.  Nr.  01385  can  be  used  for 

assembling up to two Galeo units.  

 

 

 

Summary of Contents for Galeo System





















Reviews: