Seeburg K Sub 1801 dp User Manual Download

Page: 14 / 16

K Sub 1801 dp

6 Technical specifications

Technical specifications

Speaker Components

18"

Description

Digitally Powered Bass Extension

Amp Power

1500 W AES (single Mode) 110-230 V

2400 W AES (dual Mode) 110-230 V

Rated Current

4,2 A @ 230 V

SPL

(Peak @ 1m)

137 dB

Max. Input Signal

25 dBu

DSP

HDLM FPGA Processing 32 bit floating point

AD / DA

24 bit / 96 kHz

Latency

0,8 ms (analog in to analog out)

Usable Range

(-6dB)

33 Hz - 100 / 120 / 140 Hz

Tuning Frequency

Excursion minimum

38 Hz

Connectors

Neutrik XLR in/out

Neutrik PowerCon in/out
Neutrik Speakon NL4MP out

Handles

4 x

Rigging / Fittings

M20 on top and side
Wheelboard fittings

Weight

45,0 kg
(+7,0 kg wheelboard)

Size

height x width x depth

69,8 x 51,2 x 56,0 cm

Order No.

01060/dp

The technical data sheet and further information about possible applications for the system and

available accessories can be downloaded at the following Internet address:

http://www.seeburg.net/download_getfile.php?file=downloads/06-Datenblaetter/K-Serie/K-Sub-

1801-dp_Datenblatt_dt.pdf

Summary of Contents for K Sub 1801 dp

















Search results

Summary of Contents for K Sub 1801 dp

Reviews:

Related manuals for K Sub 1801 dp

Brands by name

Popular brands

Seeburg K Sub 1801 dp, User Manual

Search results

Summary of Contents for K Sub 1801 dp

Reviews:

Related manuals for K Sub 1801 dp

Brands by name

Popular brands