background image

12

v i d e o   r e c o r d e r

Setting up the

What to do if you get picture interference

Each television programme uses a certain broadcast channel in the broadcast band. An electronic
part called the ‘modulator’ inside your video recorder sends a signal to the aerial input of your
television just like the signals sent by the television transmitters. So, the modulator uses part of
the broadcasting band and we might talk about the ‘modulator channel’.
Sometimes the modulator channel will already be used by another television station in your
reception area. In this case the picture quality on your television will be poor when the television
is receiving one or more broadcasts and the video recorder is switched on.  In severe cases of
interference you may not even recognise the video recorder picture. Here is what to do about it.

After ‘Getting started - For televisions without a scart socket’ on page 8...

• Switch your television on and select the programme number you have chosen for the video

channel (see the instruction book for your television).

• Press the POWER button on the video recorder to switch it on. In the video

recorder’s panel display, you should see ‘RF’ (flashing) followed by the
modulator channel number. If this does not appear in the display, follow ‘After auto-set’
below.

• Change the modulator channel number by pressing the number buttons 0 to 9 on the remote

control. You must choose a number from 21 to 69. The new modulator channel number will
show on the display. 

• Go back to step 6 of ‘

For televisions without a scart socket

’ on page 8 and try again.

After ‘Auto-set’ on page 13...

Press and hold the OK button on the remote control for at least five seconds
until ‘RF’ flashes in the video recorder display. The number next to  ‘RF’ is
the modulator channel number.

• Change the modulator channel number by pressing the number buttons 0 to 9 on the remote

control. You must choose a number from 21 to 69. The new modulator channel number will
show on the display.

• Tune the television in the UHF waveband until a picture like   the one below appears, and

memorise it under the video programme number. (Please read the instruction book for
your television to see how to do this.) 

• Press the POWER button on the video recorder or the 

button

on the remote control.

• Press the POWER button on the video recorder or the 

button

on the remote control again, to turn the video recorder back on.

• Check all the programme numbers that are tuned to the broadcast

stations, your video recorder and any other equipment to check
there is no picture interference. 

There is another way of changing the modulator channel, which is described in  Appendix 1 on
page 39.

Summary of Contents for VCR5360GB













































Reviews: