Seip TM 50 Installation And Programming Instructions Download | Manualshive

Page: 16 / 20

background image

Installation Instructions TM50/TM80 - MO911/1V0

Page 16

Remote Control

Registering and deleting Remote Devices

i

In order to use a remote device it must first be registered with the operator� A total of 10 remote devices may be registered
with one operator, the registration must be made seperately for each device�
If the total of 10 devices is exceeded, the last registered device will be overwritten by the new one�
It is not possible to register more than one button of the same hand transmitter with the operator�

1

Starting the Registry

Keep the red LEARN-button pressed for 3 seconds� Release it once the red LED and the operators‘ lighting start blinking�

The operator now is in programming mode and awaits the signal from a remote device�

2

Registering a Device

Press the button that shall be used for controlling the operator for approx� 1 sec�

The red LED and the operators‘ lighting stop blinking - the device was programmed successfully� Pressing the devices‘ but-
ton again will run the operator�
Repeat steps 1 and 2 for any further device�

HomeLink™

Integrated car remotes usually use the HomeLink™ system by Johnson Controls� Systems from version 6 or higher are com-
patible with the operator�
First the hand transmitter must be copied into the HomeLink™ module (closer information on your specific system can be
found on the internet: www�eurohomelink�com)�
The programmed HomeLink™ button will turn to a new Seip-compatible remote device� It therefore must be registered
with the operator just like any other remote device� Proceede as described in steps 1 + 2�

Erasing Remote Devices

The receivers‘ memory can be erased completely; it is not possible to delete single devices� To erase the receivers‘ memory
keep the red LEARN-button pressed for 10 seconds:

After 3 seconds the red LED and the operators‘ lighting will start to blink; after 10 seconds the red LED will come on perma-
nently, release the LEARN-button then� The memory now is empty�

www.thegaragedoorcentre.co.uk

0800 525 442

www.thegaragedoorcentre.co.uk

www.thegaragedoorcentre.co.uk

0800 525 442

www.thegaragedoorcentre.co.uk

«
...
14
15
16
17
18
...
»

Summary of Contents for TM 50





















Reviews:

No comments

Related manuals for TM 50

Brand: Clopay Pages: 12

Brand: FAAC Pages: 17

Brand: FAAC Pages: 44

Brand: Chamberlain Pages: 40

Brand: E.T. Systems Pages: 24

Brand: Chamberlain Pages: 88

Brand: Chamberlain Pages: 180

Brand: DACE Pages: 22

Brand: TMT Pages: 8

Brand: TMT Automation Pages: 16

Brand: DPLUS Pages: 8

Brand: DPLUS Pages: 12

Brand: CAME Pages: 72

Brand: Beninca Pages: 24

Brand: Beninca Pages: 24

Brand: Zero Pages: 12

Brand: Zero Pages: 12

Whisper Drive Security+ 459950

Brand: Chamberlain Pages: 88

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands