background image

 

 

FCC NOTICE 

 

 
 

THIS DEVICE COMPLIES WITH PART 15 OF THE FCC FULES. 
OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITION: 
(1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND 
(2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED,   
INCLUDING INTERFERENCE THAT MAY CAUSE UNDERSIRED   

OPERATION.  

 
 
 
 
This equipment has been tested and found to comply with the limits for a Class B digital device, 
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection 
against harmful interference in a residential installation. This equipment generates, uses and can 
radiate radio frequency energy and, if not installed and used in accordance with the instructions, 
may cause harmful interference to radio communication. However, there is no guarantee that 
interference will not   
occur in a particular installation. If this equipment does cause harmful interference to   
radio or television reception, which can be determined by turning the equipment off and on, the 
user is encouraged to try to correct the interference by one or more of the following measures :   
 
- Reorient or relocate the receiving antenna.   
 
- Increase the separation between the equipment and receiver.   
 
- Connect the equipment into an outlet on a circuit difference from that to which   
    the receiver is connected.   
 
- Consult the dealer of an experienced radio/TV technician for help.   
 
 
NOTE : The manufacturer is not responsible for any radio or TV interference caused by   
unauthorized modifications to this equipment. Such modifications could void the user’s   
authority to operate the equipment.   

Summary of Contents for SKR-2006










Reviews: