background image

0000137188                                                          Rev. 1.0 

 

 

14 

9.2 

ON/OFF pH dosing 

The instrument allows the chemical measurement to be controlled and modified through 
the pH  Set  Point  automatically;  adjusting  the  dosing  though  the pH  motor  controlled  in 
ON/OFF. 
The dosing below is obtained by setting the following parameters: 
 

  Set point pH = 7.20 pH 

  Type of Dosing = Alkaline 

Set Point pH

Motore pH

 

 

 
9.3 

Alarm for the pH Set Point 

 

When the alarm band is set, a work window is created. If the allowed limits are exceeded the alarm relay 
closes and remains closed until the measurement is reset or the enter key is pressed to deactivate the 
alarm. 
 
When the OFA time (Over Feed Alarm) is set, the dosing time of Set Point pH in time is controlled with two 
alarms: 
 

  First alarm at 70% of the time set is seen on the display, the alarm relay closes. 

  Second alarm at 100% of the time set is seen on the display and the alarm relay closes and the 

pH motor is blocked. 

 
Press the Enter key to eliminate the alarm and initialise the OFA time. 
 

Motore pH

Set Point pH

ALR Relè

ALR Band

ALR Band

 

Summary of Contents for Pool Basic Pro Evo




















Reviews: