Sekonic SR-450 Operating Manual Download

Page: 17 / 75

3.Specifications

3. Specifications

1. Available cards

Card size: Standard-sized card, postcard-sized card, long-sized card

Paper type: OCR paper.

※

Refer to 13.A-(1)

Paper ream weight: (70)* 90kg to 135kg

(basic weight: (83.8g/m

) 104.7g/m

to 157.0g/m

)

(thickness: (0.11mm) 0.13mm to 0.19mm)

The 70kg paper is available to standard size only.

2. Mark line number

Standard-sized card: Data = 12 lines, timing = 1 line

Postcard-sized card: Data = 15 lines, timing = 1 line

3. Mark column

Max. 140 columns. (specified by program)

4. Reading method

Direct-under type, timing control type, mark-to-mark type

5. Marking

Infrared ray: Pencil of HB or softer, machanical pencil

[visible ray: The above, ball-point pen]

6. Reading wavelength:

Infrared ray: 940nm

[visible ray: 660nm]

7. Card feeding rate

Approx. 256 sheets/min (115V AC/50Hz, machine feeding rate using

standard-sized cards at room temperature)

8. Hopper capacity

Max. 200 cards. (paper of ream weight of 110kg (basis weight of 127.9g/

), standard-sized card)

9. Error check

Four types of errors can be judged (jam, timing mark, card empty and

double-feeding errors)

10. Self-check

The card detection sensor is to be checked.

11. Serial Interface

Serial EIA RS-232C-based, asynchronous, half-duplex,

data transfer rate = 2,400 to 115,200bps (variable)

variable data format

12. USB interface

USB 2.0 full-speed

Virtual COM Port Device

(same specification as 11.Serial interface)

13. Power supply

Supply voltage = 115V AC, Frequency = 60Hz

Current = Approx. 0.6A (during motor rotation)

Approx. 0.1A (in standby mode)
Supply voltage = 220V AC, Frequency = 50/60Hz

Current = Approx. 0.3A (during motor rotation)

Approx. 0.1A (in standby mode)

14. Operating environments Room temperature = 5 to 35C˚

Relative humidity = 40 to 80% RH (no dew condensation)

15. Overall dimensions

360 (L) x 222 (W) x 171 (H) (mm)

(Length in operation: 695 mm)

16. Weight

Main unit = Approx. 6kg

[ ] is option

4.Installing the USB Driver

4-A Before Installation

To use a USB interface connection, load the supplied CD-ROM, and install the driver by following
the installation procedure in this chapter.
Be sure to install the USB driver before inserting the SR-450 into the computer's USB port. The
driver cannot be installed properly if the SR-450 is inserted into the USB port first.

Notes
• If you accidentally connect the SR-450 before performing the installation, delete the falsely-

identified driver from "Add or Remove Programs".

• To install the driver, you must log in as a user with administrator privileges.

Operating Environment

* • The OS must be preinstalled.

•  The software may not work for certain computer models and configurations.
•  Operation is not guaranteed for systems with an upgraded OS, add-on USB interface, self-
  built computers, built-to-order computers, and in emulator environments (such as VirtualPC).
• Operation is not guaranteed for connections that pass through a USB hub.
•  A drive capable of reading CD-ROMs is required for installing the software.

4. Installing the USB Driver

The USB driver must be installed to use this product over a USB interface connection. If using this
product over a RS-232C connection, the driver does not need to be installed, and the procedures in this
chapter are not necessary.

Get the latest information at our website. (https://www.sekonic.co.jp/english)

Windows 8.1/10

- 5 -