13
TPS_ED1401-ENIT
Standards
Norme
IEC Standards
TPS is manufactured and tested in conformity with the latest
issues of the following IEC standards.
IEC 62271-1
Common specifications for high voltage switchgear
and controlgear.
Ambient temperature:
Maximum value: 40°C
Maximum value of 24 hours average: 35°C
Minimum value: –5°C
Altitude of installation:
Up to 1000 m.
Above 1000 m. consult SEL S.p.A.
IEC 62271-200
A.C. Metal enclosed switchgear and controlgear
for rated voltage above 1kV and up to 52kV
Switchgear classification:
PI class (metallic partitioning)
Loss of service continuity:
LSC2A
Internal arc classification:
class AFL to 12.5kA /1s (access
restricted to authorized personnel only for front and lateral access)
on request: AFLR - 16KA / 1s
IEC 62271-103
High voltage switches for rated voltage above
1kV and up to 52kV
Class M1/E3
•
1000 operating cycles close/open.
•
100 make-break operating cycles at 100% mainly active load
test duty 1 (rated current and 0.7 power factor).
IEC 62271-100
High voltage alternating current circuit breakers
Standard circuit-breakers have class M1/E1.
Circuit-breaker class M1:
circuit-breaker with normal mechanical
endurance, type tested for 2000 mechanical operations.
Circuit-breaker class E1:
circuit-breaker with basic electrical
endurance not falling into class E2 (no extra tests are therefore
required beyond the normal short-circuit type test).
On request class M1/E2 or class M2/E2 circuit-breakers are also
available.
Circuit-breaker class M2:
circuit-breaker with extended
mechanical endurance, type tested for 10000 mechanical
operations.
Circuit-breaker class E2:
circuit-breaker with extended
electrical endurance specifically type tested operating sequence
(see tab.21 §6.112 of IEC 62271-100).
Rated operating sequence:
O-t-CO-t’-CO
where:
•
t=3 min for circuit-breaker not intended for rapid auto-
reclosing
•
t=0,3 s for rapid auto-reclosing circuit-breakers
•
t’=3 min
IEC 62271-102
Alternating current disconnectors and earthing
switches.
IEC 62271-105
Alternating current switch - fuse combination.
IEC 60529
Degrees of protection provided by enclosures (IP
code).
Rispondenza normativa internazionale.
Il TPS è costruito e collaudato in conformità con le emissioni più
recenti dello standard IEC di seguito elencate.
IEC 62271-1
Prescrizioni comuni per l’apparecchiatura di
comando e di manovra ad alta tensione.
Temperatura ambiente:
Valore massimo: 40°C
Valore massimo della media sulle 24 ore: 35°C
Valore minimo: -5°C
Altitudine di installazione:
Fino a 1000 metri
Oltre 1000 metri consultare SEL S.p.A.
IEC 62271-200
Apparecchiatura prefabbricata con involucro
metallico per tensioni da 1kV a 52kV
Classificazione del quadro:
Classe PI
Continuità di servizio:
Classe LSC2A
Classificazione per tenuta arco interno:
Classe AFL 12.5KA
per 1s (Accesso di personale autorizzato al fronte ed ai lati del
quadro) a richiesta: AFLR - 16kA / 1s
IEC 62271-103
Interruttori di manovra ed interruttori di
manovra sezionatori per alta tensione
Classificazione: M1/E3
•
1000 cicli di operazioni chiusura/apertura.
•
100 cicli di operazioni stabilimento/interruzione al 100% della
corrente di carico prevalentemente attivo come prescritto dal
ciclo di prova 1 (corrente nominale e cosΦ 0.7).
IEC 62271-100
Interruttori per alta tensione in corrente
alternata. I nostri interruttori di fornitura standard sono classificati
M1/E1.
Interruttore Classe M1:
interruttore con durata meccanica
normale (sottoposto a prove di tipo meccaniche per 2000
manovre).
Interruttore Classe E1
: interruttore con durata elettrica di base
che non rientra nella categoria E2 (non sono necessarie prove
supplementari oltre la normale prova di cortocircuito).
A richiesta, sono disponibili interruttori di classe M1/E2 oppure
interruttori M2/E2.
Interruttore Classe M2:
interruttore con durata meccanica
estesa (sottoposto a prove di tipo meccaniche per 10000
manovre).
Interruttore Classe E2:
interruttore con durata elettrica estesa
sottoposto ad una specifica sequenza operativa di prova (vedi
tab.21 §6.112 della normativa IEC 62271-100).
Sequenza di operazione nominale:
O-t-CO-t’-CO
dove:
•
t=3 min : per interruttori non previsti per la richiusura rapida
•
t=0,3 s : per interruttori previsti per richiusura rapida
•
t’=3 min
IEC 62271-102
Sezionatori e sezionatori di terra a corrente
alternata e a tensione superiore a 1000 V.
IEC 62271-105
Interruttori di manovra-sezionatori combinati
con fusibili ad alta tensione per corrente alternata.
IEC 60529
Gradi di protezione (codice IP).
CEI-016
Regola tecnica di riferimento per la connessione di
utenti attivi e passivi alle reti AT e MT delle imprese distributrici
di energia elettrica.