background image

Portable Use 

Batteries and Connections 

By using optional battery clips, the LD350-24 can be connected directly to 
a vehicle battery. When using Alligator clips ensure they have a tight grip 
around the battery post. Wherever possible battery connections should be 
bolted. If connecting the LD350-24 through a cigarette lighter socket the 
maximum power output of the LD350-24 will be 

severely

 restricted, this 

practice should be avoided. Check with your supplier or installer if you are 
unsure.

 

Batteries are the key to maximum performance from your LD350-24, if a 
battery is too small or not fully charged it may result in de-rated 
performance from your LD350-24.

 

Battery ratings 

Batteries can be rated in one of two ways: 
1.

 

CCA = Cold Cranking Ability. This is the amount of power or current that 
a battery can deliver for a short period, typically a few seconds. This how 
a car battery would normally be rated. 

 
Do not use alligator clips in a moving vehicle 

 

Auxiliary Battery

Earth (to chassis)

LD350-24 Inverter

Earth (to chassis)

Isolator

Vehicle
Alternator

 

2.

 

Ah = Ampere Hours. This is the maximum amount of energy that can be 
stored in a battery; this figure will generally be stated at a particular hour 
rate. This is how a deep cycle or storage battery would normally be rated. 

Start Battery

 

By incorporating an auxiliary battery in the manner above, the starting battery 
should remain charged for vehicle starting (see your auto electrician). 

The LD350-24 has sufficient battery cable length to allow it to sit underneath the vehicle 
whilst in use. If the ground is wet, place the LD350-24 on a waterproof liner. 

LD350-24 Manual 

 

Selectronic Australia

 

100Ah @100hr, this means that when this battery is discharged over 
a period of 100 hours, the battery has a capacity of 100Ah. This in 
theory means 1 Amp for 100 hours, although this would in practice 
result in a totally discharged battery that may not then recover. 

 

 

To achieve maximum performance from your LD350-24 you must have a 
battery capable of delivering 75 Amps for a short period whilst 
maintaining at least 21.0 volts. To increase the capacity of your battery you 
may need to join more than one battery together.

 

 

 

Where batteries are joined 
in 

series

, add the voltage of 

each battery. 

 
 
 

The capacity will equal the capacity of the smallest battery. 2 x 12 
Volt 150 Ah batteries connected in series would have a total 
capacity of 24 Volts – 150 Ah.  

 

 

LD350-24 Manual 

 

Selectronic Australia

 

Summary of Contents for LD350-24











Reviews: