background image

Product Warranty Conditions 

LD350-24 Volt Specifications 

Inverter Type

 Microprocessor control circuit with PWM full bridge power 

stage. True sine wave AC output 

 

Warranty 

Selectronic Australia Pty Ltd warrants your inverter to be free from 
defects in materials and workmanship under normal use and service, 
for an initial period of two (2) years. Defective parts will be replaced 
or repaired free of charge within this period. 

Conditions 

This warranty is applicable only from the date of original purchase.

 

The provision of this warranty shall not apply if the unit has been 
subject to misuse, neglect, act of God, accidental damage or has been 
used for a purpose for which it is not intended. 

Unauthorised modification or repair will void your warranty. 

To ensure a smooth and speedy response to your warranty claim, 
please complete and return your reply paid warranty card within 30 
days from date of purchase. 

 

Within Australia & New Zealand 

The inverter must be returned, at the owner’s cost, to an authorised 
service centre listed in this manual. There will be no charge for the 
return of the inverter.  

 

Outside Australia & New Zealand 

Product purchased for use outside Australia & New Zealand must be 
returned to Selectronic Australia’s Service Centre to enable warranty 
claims to be processed. Freight cost to be borne by the customer. No 
charge will be made for the product return. 

 

Current draw from Battery 

Condition 

Amperage 

Demand Start SLEEP mode (average) 

Inverter ON, with no Load 

Maximum Continuous Load (350 Watt) 

Half hour rating (450 Watt) 

Surge rating (1000 Watt) 

0.05 Amps 

0.35 Amps 

15 Amps 

 23 Amps 

 46 Amps 

 

Inverter Power Ratings @ 25

º

 C 

Total Inverter output 

Condition 

Wattage @ 1.0pf 

Current 

Continuous  

Half hour rating 

Surge rating (5 seconds) 

350 Watt 

450 Watt 

1000 Watt 

1.9 Amps 

 2 amps 

 3.5 Amps 

 

Demand Start 

 

Type  

Minimum Load to Start 

Response Time Normal Pulse Mode 

Pulsing AC 

4 watts – 16 watts user adjustable 

1 second maximum 

 

Battery Voltage Range 

Voltage 

Low DC Volts Cut Out–10 second delay 

Low DC Volts Cut In 

High DC Volts Cut Out–Instantaneous 

20 – 23 volts user adjustable 

24 volt 

34 volts 

 

LD350-24 Manual 

 

Selectronic Australia

 

15 

 

LD350-24 Manual 

 

Selectronic Australia

 

16

Summary of Contents for LD350-24











Reviews: