background image

SE10 Manual

14

Selectronic Australia

3.

 

Once a fortnight or as directed in your battery manufacturer, check the
specific gravity (SG) of each battery cell using a hydrometer, to ensure
that all cells are performing correctly and are properly charged. Any
serious imbalance should be reported to your system designer in case
remedial action needs to be taken.

Solar Modules

 

Periodically check for a build up of dust or any other foreign matter.

Wind Generator

 

As wind generators are mechanical devices that are subject to weather
variances, proper maintenance is essential for reliable service.

 

Carefully follow the manufacturers maintenance guidelines; if unsure
contact your supplier.

Handy Hints

It is very important that you become familiar with the
functioning of your inverter. From a distance, it is not always
easy to know what if the inverter is On or in Sleep mode. An
easy way to determine this is to plug a small child's night light
(neon type) into a power point that is easily visible, or replace
this power point with a safety type with a neon indicator. This
will indicate the inverter's operation by flashing when the
inverter is in SLEEP mode and remaining ON when the
inverter is brought ON by a load.

Summary of Contents for SE10

























Reviews: