SELECTRONIX SLC4075 Series Installation & Operating Manual Download | Manualshive

Page: 18 / 28

background image

www.selectronix.us

Selectronix, Inc.

(425) 788-2979

SLC4075 TouchScreen Gateway Installation & Operating Manual

___________________________________________________________________________________________________

18

SLC4060 Relays

a.

Source Selector defines the signal which activates the relay

a.

0 = Disabled

b.

1 = GPDIx, the corresponding GPDIx operates the relay.

c.

2 = GPDIx and GPDI4 the corresponding GPDIx And’ed with GPDI4 operates the relay.

d.

3 = GPDIx and GPDI4 the corresponding GPDIx Or’ed with GPDI4 operates the relay.

e.

4 = DDC, Building Management System operates

f.

5 = SLC4000 Fault

g.

6 = PGW & Cmd=0 Fault

h.

7 = TSGW Fault

i.

8 = Combines #2 and #6 above

j.

9 = Combines #3 and #6 above

b.

Relay Invert Mask is used to invert the logical source signal to operate the relay.

a.

Note that an inverted relay reverts to normally open on AC power loss.

Expansion Relays

a.

8 additional relays may be added by using a standard SLC4000 with the “Dedicated Test” position selected, (SW2-
1 Off). This sets an SLCnet pre-determined address and “Expansion Relay mode” operation. The dedicated test
functions for ‘Test Up’ and ‘Test Dn’ remain, as does the Status indication.

b.

Source Selector defines the signal which activates the relay according to the following table:

SrcSel

XRly1

XRly 2

XRly 3

XRly 4

XRly 5

XRly 6

XRly 7

XRly 8

0

Disabled Disabled Disabled Disabled Disabled Disabled

Disabled Disabled

1

XDIx

XDIx

XDIx

XDIx

XDIx

XDIx

XDIx

XDIx

2

XDIx

XDIx

XDIx

XDIx

PGW
Flt

TSGW
Flt

S4K Flt

Rsv Flt

3

XDIx

XDIx

XDIx

XDIx

BMS

BMS

BMS

BMS

4

BMS

BMS

BMS

BMS

BMS

BMS

BMS

BMS

SLC4060 Voltage Driver

a.

Source Select defines the signal that is sent to the voltage driver

a.

0 = Disabled

b.

1 = RTD1

c.

2 = RTD2

d.

3 = GPA1

e.

4 = GPA2

f.

5 = PID1 0-10 V dc

g.

6 = PID1 2-10 V dc

h.

7 = PID2 0-10 V dc

i.

8 = PID2 2-10 V dc

j.

9 = BMS

SLC4060 Information

a.

PGW Firmware Version:

b.

Remote Enable Code:

a.

90 is the default enable code

b.

0 is the default disable code

c.

PGW Step Cmd % is the step command originating from either PID1, PID2, or a PGW BMI.

d.

PGW Ld Lmt % originating from a PGW BMI.

e.

PGW On Dly Sec originating from a PGW BMI I

f.

PGW Fault

g.

MSTP Addr is the setting of the MSTP address by DIP switch SW2.

«
...
16
17
18
19
20
...
»

Summary of Contents for SLC4075 Series





























Reviews:

No comments

Related manuals for SLC4075 Series

Brand: System Sensor Pages: 10

ASinterfoce AC1325

Brand: IFM Electronic Pages: 23

Brand: OleumTech Pages: 104

Brand: Berker Pages: 4

Brand: ABB Pages: 11

Brand: Banner Pages: 110

Brand: PREDICTWIND Pages: 16

Brand: Alcatel-Lucent Pages: 4

Brand: Wireless Devices Pages: 32

Brand: Hans Turck Pages: 53

Brand: ATX Pages: 30

Brand: ATX Pages: 32

Brand: Mavix Pages: 73

Brand: Lucent Technologies Pages: 116

Brand: Lucent Technologies Pages: 2

Brand: H3 System Pages: 12

Brand: TECOM Pages: 139

Brand: TANDBERG Pages: 17

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands