background image

SELVAS Healthcare, Inc. 

 

14

_ABOUT BODY COMPOSITION 

 

Abdominal Fatness 

Body fat is divided into subcutaneous fat and visceral fat. Visceral obesity is considered to be a critical risk 
factor along with Percent of body fat. 

Lipoprotein lipase can be easily activated in visceral fat, and it cause visceral fat to be dissolved easily. 
Dissolved visceral fat goes into liver through the vessel and it cause fatty liver or increasing lipid in the 
blood. It also elevates the risk of hyperinsulinemia, hypertension, and cardiovascular disease. 

Visceral  fat  generally  occupies  10  ~  20  %  of  body  fat,  and  visceral  obesity  is  assessed  based  on  the 
indicators below. 

 

the cross sectional fat area between L4 ~ L5 is 100 cm

2

 and over 

 

the visceral fat to subcutaneous fat ratio is 0.4 and over 

 

the waist to hip ratio (W.H.R.) is over 0.9 (male) / 0.85 (female) 

 

the circumference of waist is over 102 cm (male) / 88 cm (female) 

Visceral fat increases after their 30s in men and after Menopause in women. It is more common in men 
than women and the old than the young. Visceral fat tends to increase with aging. Because the combustion 
rate per minute of visceral fat is higher than that of subcutaneous fat, visceral fat can be easily reduced 
by exercise or dietary control in case of abdominal obesity. W.H.R. is the ratio of waist to hip circumference 
and has relation to one

s figure. 

Segmental Analysis 

This device analyzes soft lean mass of five body parts; trunk, right arm, left arm, right leg, and left leg. 
This function can be used as an assessment tool to evaluate the result of exercise or rehabilitation treatment. 

Age Matched of Body 

It is the estimated physical age of the subject considering body composition analysis result, gender, and 
biological age. This is calculated by comparing the optimal body composition based on the gender and 
biological age of the subject with the actual analyzed body composition. It can be used to evaluate the 
subject

s health and body development. 

 

 

Summary of Contents for ACCUNIQ BC300









































































Reviews: