semaphore KINGFISHER PLUS+ Hardware Reference Manual Download | Manualshive

Page: 179 / 247

background image

Kingfisher Plus+ Hardware Manual

Note:

Link terminals can be optionally connected to the adjacent Common terminals to enable the

Fuse Monitor LED (FU).

Caution:

A maximum of 30 V (AC or DC) can be used to power the common if the link is installed.

Wiring Example

Notes:

1.

Polarity can be reversed.

2.

For safety reasons, do not connect more than one power source to a Digital Out Common
terminal.

3.

If power supply voltage exceeds SELV levels (DC 60 V or AC 42 V

PEAK

relative to

system earth and/or ground) then both Common Terminals of the module must be
connected to a single power source and no other power sources can be connected to
the same module.

LOAD Z

LOAD Y

Channel Z

Channel Y

Common

Power

Supply

+

_

LOAD X

Channel X

Hardware Manual Version 7.16

http://www.servelec-semaphore.com/

Page 179

«
...
177
178
179
180
181
...
»

Summary of Contents for KINGFISHER PLUS+
























































































































































































































































Reviews:

No comments

Related manuals for KINGFISHER PLUS+

Brand: Accu-Chek Pages: 12

Brand: Facom Pages: 42

Brand: Midcontinent Pages: 6

CoolPoint CP12-V8

Brand: UFM Pages: 14

Nitro-Save NS16

Brand: TDI Pages: 4

Brand: JUMO Pages: 24

Brand: DODODUCK Pages: 2

Brand: Spasciani Pages: 26

Brand: SIGLENT Pages: 32

Brand: Sper scientific Pages: 12

Scuba MAXIMUS SRB3600 regulator

Brand: Sherwood Scuba Pages: 29

Trimble Ranger 3

Brand: Badger Meter Pages: 20

Brand: A&D Pages: 38

In-Situ Rugged TROLL 100

Brand: Geotech Pages: 6

Brand: Young Pages: 7

ProSense LPM1 Series

Brand: Automation Direct Pages: 29

Brand: DigiTech Pages: 11

Brand: Micromeritics Pages: 254

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands