semaphore KINGFISHER PLUS+ Hardware Reference Manual Download

Page: 7 / 247

Kingfisher Plus+ Hardware Manual

6.8.1 Line Board Connections...................................................................................... 107

6.8.2 Connecting a Radio ............................................................................................ 108

6.8.3 2-Wire Line, point-to-point ................................................................................... 109

6.8.4 2-Wire Line, multi-drop........................................................................................ 109

6.8.5 4-Wire Line, point-to-point ................................................................................... 110

6.8.6 4-Wire Line, multi-drop........................................................................................ 110

Option Board H: HART Interface .............................................................................. 113

6.9.1 HART Board Connections ................................................................................... 113

Option Boards T3 & T2: 10/100 Ethernet Controller................................................ 116

Option Board A3: Fibre Optic Ethernet ................................................................... 117

Option Board R2: Australian Spread Spectrum Radio ............................................ 118

Option Board R3: International Spread Spectrum Radio ......................................... 120

Option Board R4: US/Canada Spread Spectrum Radio .......................................... 122

7. PC-1 OPTION BOARDS ........................................................................ 124

PC-1 Serial Option Board ......................................................................................... 124

PC-1 Modem Board PL: Two Wire Line .................................................................... 125

PC-1 Modem Board: Analogue Radio Interface ........................................................ 126

8. IO MODULES OVERVIEW ..................................................................... 127

9. ANALOGUE INPUT MODULES .............................................................. 131

AI-1: 8 Channel Analogue Current Input Module ...................................................... 131

9.1.1 Overview ............................................................................................................ 131

9.1.2 AI-1 Module LEDs ............................................................................................... 133

9.1.3 AI-1 Specifications .............................................................................................. 134

9.1.4 AI-1 Wiring Diagram ........................................................................................... 135

AI-10: 8 Channel High Impedance Analogue Input Module ...................................... 137

9.2.1 Overview ............................................................................................................ 137

9.2.2 AI-10 Module LEDs ............................................................................................. 140

9.2.3 AI-10 Specifications ............................................................................................ 141

9.2.4 AI-10 / AI-10-V Wiring Diagram ........................................................................... 142

10. ANALOGUE OUTPUT MODULE ........................................................... 144

AO-3: Analogue Output Module .............................................................................. 144

10.1.1 Overview........................................................................................................... 144

10.1.2 AO-3 Module LEDs ........................................................................................... 146

10.1.3 AO-3 Specifications .......................................................................................... 147

10.1.4 AO-3 Wiring Diagram ........................................................................................ 148

11. DIGITAL INPUT MODULES ................................................................. 150

Overview ................................................................................................................ 150

DI-5: DC Input 16 Channel Digital Input Module ..................................................... 150

11.2.1 Overview........................................................................................................... 150

11.2.2 DI-5 Module LEDs ............................................................................................ 151

11.2.3 DI-5 Specifications ............................................................................................ 152

11.2.4 DI-5 Wiring Diagram ......................................................................................... 153

Summary of Contents for KINGFISHER PLUS+
























































































































































































































































Search results

Summary of Contents for KINGFISHER PLUS+

Reviews:

Related manuals for KINGFISHER PLUS+

Brands by name

Popular brands

semaphore KINGFISHER PLUS+, Hardware Reference Manual

Search results

Summary of Contents for KINGFISHER PLUS+

Reviews:

Related manuals for KINGFISHER PLUS+

Brands by name

Popular brands