semaphore KINGFISHER PLUS+ Hardware Reference Manual Download | Manualshive

Page: 28 / 247

background image

Kingfisher Plus+ Hardware Manual

Linking Backplanes

2.5.1 Creating Racks

A single RTU can consist of up to 64 modules by using a six-bit number adopted in the
Kingfisher Plus+ systems:

In order to organise connection of up to 64 modules into one RTU, backplanes should be
linked together into ‘racks’. Each rack can have a maximum of 16 slots. A single RTU can
support up to 4 racks thus providing a total of 64 module slots.

The figure below shows one full rack (16 slots) consisting of a

linked to a

12-PLUS

.

The BA-x-PLUS backplanes have an IN and an OUT connectors (J13 and J15 described
earlier in the “

Backplane Connectors

” section) linking them to the RTU data bus. The BP-x-

PLUS backplanes have only one (OUT) connector linking them to the RTU data bus (J13).
The reason for this is that the BP-x-PLUS backplane must always be the first in an RTU.

Hardware Manual Version 7.16

http://www.servelec-semaphore.com/

Page 28

«
...
26
27
28
29
30
...
»

Summary of Contents for KINGFISHER PLUS+
























































































































































































































































Reviews:

No comments

Related manuals for KINGFISHER PLUS+

Brand: Banner Pages: 11

Brand: Bante Instruments Pages: 10

Brand: BANTE Pages: 11

Brand: Banner Pages: 14

Brand: Banner Pages: 16

Brand: Hammond Pages: 130

Brand: Waterproof Pages: 10

Brand: Ocean Optics Pages: 43

Brand: Ocean Technology Systems Pages: 12

Brand: Ocean Reef Pages: 24

Brand: G-Tek Pages: 83

VOLUTANK Petro 3003

Brand: Bartec Pages: 10

Brand: Topcon Pages: 62

Brand: Velleman Pages: 107

Brand: FISCHER Pages: 20

Brand: RS PRO Pages: 44

Brand: International Light Technologies Pages: 19

Brand: Ralcam Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands