background image

IMPORTANT

Please read these instructions carefully before you start to assemble this carport.
Please carry out the steps in the order set out in these instructions.
Keep these instructions in a safe place for future reference.

 Care and Safety advice
* Please follow the instructions as listed in this manual.
* Sort the parts and check against the list of contents.
* For safety purposes we strongly recommend that the product will be assembled
  by at least two people
* Some parts have metal edges. Please be careful when handling components.
* Always wear gloves, shoes and safety goggles during assembly.
* Do not attempt to assemble the carport in windy or wet conditions.
* Dispose of all plastic bags safely - keep them out of reach of small children.
* Keep children away from the assembly area.
* Do not attempt to assemble the carport if you are tired, 
* When using a stepladder or power tools, ensure that you are follow the
  manufacturer's safety advice.
* Do not climb or stand on the roof.
* Heavy articles should not be leaned against the poles.
* Please consult your local authorities if any permits are required to erect carport.
* Keep roof and gutters clean of snow, dirt & leaves.
* Heavy amounts of snow on roof can damage the carport making it unsafe to
  stand below or nearby.
* This product was designed and produced to be a carport only.

 PREPARATION  OF GROUND

Before Starting Assembly
This carport must be assembled on a solid base,

Choose your site carefully before beginning assembly. Site surface (mainly below 
poles) needs to be level.

50 cm 

50 cm 

50 cm 

Concrete

MAINTENANCE NOTES

1. In case of a defective or damaged part, or for any other questions concerning
    the product, please contact the manufacturer directly.
2. Please have the parts list and part numbers on hand when ordering or
    requesting replacement parts.
3. When cleaning, use mild soap or detergent, warm water, and a washcloth or sponge.
4. While the product is designed for 4 seasons use, it is strongly recommended to 
    clear snow from the roof on a regular basis.

LIMITATIONS ON THE WARRANTY

1. The product is not warranted against damages due to vandalism, abuse, or falling 
    or thrown objects.
2. The product is not warranted against damages due to extreme weather conditions,
    such as thunderstorms, hail, strong wind or snow storms, or any other acts of God.
3. The product is only warranted in the event it is installed in accordance with the 
    Transpa Forza written instructions enclosed with the product.
4. The product is not warranted in the event it has been improperly anchored.

The carrier profiles  must be buried in pits, anchored and should be filled 
with concrete

Prepare the holes  of  50x50x50 cm for all the post.
Make a anchorage ,and fill with  concrete

Summary of Contents for TRANSPAFORZA TF-P2











Reviews: