EN-8
EN
Blender
SBL 3271SS / SBL 3272RD
2015
11/2015
Attention:
The safety mechanism will prevent the appliance from being started unless the blending jar or
grinder assembly is properly attached to the motor unit A
7
.
3.2 To remove the blending jar or grinder from the motor unit A
7
, proceed in the reverse sequence.
OPERATING THE APPLIANCE
1. Using the blender
1.1 Make sure that the motor unit A
7
is turned off and disconnected from the mains power socket.
1.2 Assemble the blender according to the instructions in chapter Assembling and disassembling the
appliance.
1.3 Place the food or pour the liquids that you wish to blend into the blending jar A
3
. Close the
blending jar A
3
using the lid according to the instructions in chapter Assembling and disassembling
the appliance.
Note:
The maximum capacity of the blending jar A
3
is 800 ml. We recommend that the blending jar is
not filled with more than 600 ml of liquids. Certain liquids increase their volume during mixing,
and therefore it is better to blend them gradually in smaller batches.
1.4 Connect the power cord to the power socket and set the speed dial A
8
to the required speed
level of 1 or 2. Level 1 is slower and level 2 is faster. We recommend to first set the slower speed to
allow the ingredients to mix together. Then you can increase the speed to level 2. While blending,
always use your hand to hold down the lid A
2
from above. The pulse level is appropriate when
you wish to blend food only very quickly. To start the pulse level, turn the speed dial A
8
to the
position "P" and hold it in this position for a moment. As soon as you release the speed dial A
8
, it
will automatically return to position 0 (Off).
Attention:
The maximum operating time is 2 minutes. Do not leave the appliance in continuous operation
for longer than indicated above. Then allow the appliance to cool down for 2 minutes. When
processing hard food or liquids with a very thick consistency, do not leave the appliance in
continuous operation for longer than 1 minute.
1.5 While blending, you may add food or liquids to the blending jar A
3
through the hole i the lid A
2
after removing the inner cap A
1
.
1.6 In the event that food is sticking to the blade assembly A
5
or the walls of the blending jar A
3
,
turn the appliance off by turning the speed dial to position 0 (Off) and disconnect it from the
power socket. Make sure that the blade assembly A
5
has stopped rotating. Carefully remove the
blending jar from the motor unit A
7
. Take off the lid A
2
and using a plastic spatula clean the
blade assembly A
5
and the walls of the blending jar A
3
. Put the lid A
2
back on and reattach
the blending jar to the motor unit A
7
. Plug the power cord into a power socket and continue
blending.
1.7 After you have finished using the appliance, set the speed dial A
8
to position 0 (Off) and disconnect
the power cord from the power socket. Check that the blade assembly A
5
has stopped rotating
and take the blending jar off the motor unit A
7
. Use a soft plastic spatula to remove food from
the blending jar A
3
.
1.8 Disassemble the blending jar according to the instructions contained in chapter Assembling and
disassembling the appliance, and clean it according to the instructions in chapter Cleaning and
maintenance.
2. Using the grinder
2.1 Make sure that the motor unit A
7
is turned off and disconnected from the mains power socket.
2.2 Place the food that you wish to grind up into the grinding jar A
0
. The grinder is suitable for
grinding nuts (with shells removed), coffee beans, spices, etc. The maximum amount of food
that can be placed in the jar A
0
is indicated by the MAX mark. Do not overfill the jar A
0
.