- 6 -
03/2021
Copyright © 2020, Fast ČR, a.s.
EN
Humidifier
User's manual
■
Prior to using this appliance, please read the user's manual thoroughly, even in cases,
when one has already familiarised themselves with previous use of similar types of
appliances. Only use the appliance in the manner described in this user’s manual.
Keep this user's manual in a safe place where it can be easily retrieved for future use.
■
We recommend saving the original cardboard box, packaging material, purchase
receipt and responsibility statement of the vendor or warranty card for at least the
duration of the legal liability for unsatisfactory performance or quality. In the event
of transportation, we recommend that you pack the appliance in the original box
from the manufacturer.
DESCRIPTION OF THE APPLIANCE
A1
Steam outlet
A2
Control panel
A3
Motor unit with a fan
A4
Power adapter connection socket
(located at the rear)
A5
Float switch limiter
A6
Float switch
A7
Humidifying filter
A8
Motor unit release clip
A9
Vents
A10
Water tank
A11
Water level with MAX mark
A12
Power adapter
DESCRIPTION OF THE CONTROL PANEL
B1
Button
- illumination / sleep
mode selection
B2
Button
AUTO
- automatic mode
selection
B3
Button
- fan speed selection
B4
Humidifying filter replacement
indicator light
B5
Button
- On / Off
BEFORE FIRST USE
■
Before first use, take the appliance and its accessories out of the packaging material
and remove all promotional labels and stickers. Check that neither the appliance nor
any of its parts is damaged.
Filling the water tank
1. Place the appliance on a firm, level and water-resistant surface. To achieve better
performance, check that the appliance is located at least 10 cm away from walls.
2. To ensure optimal operation, ensure that neither the vents nor the steam outlets are
blocked.
3. Ensure that neither the power adapter cord nor its plug are damaged.
4. Press the safety clip
A8
and carefully lift up the motor unit
A3
.
5. In the event that there is a protective cover on the humidifying filter
A7
, take it off
and remove the float switch
A6
.
6. Pour clean cold water into the water tank
A10
up to the MAX mark.
7. Insert the float switch
A6
and then insert the humidifying filter
A7
with the limiter
A5
attached so that the float switch
A6
can freely move through the hole in the
middle.
8. Put the motor unit
A3
back on.
9. Insert the connector of the power adapter
A12
into the socket
A4
and insert the
power adapter plug into a properly grounded power socket. A sound is made and
the humidifier is ready for use.
Turning on / off
■
Press button
B5
to start the humidifier. The humidifier will automatically start
at speed
II
. The backlight underneath the control panel A2 will gradually change
through all the colours. The indicator lights "
LIGHT
" and "
II
" will be lit blue.
■
When not using the humidifier, press button
B5
to turn the humidifier off.
Button
■
Button
B1
serves to turn the coloured backlight on and off, and to turn the sleep
mode on and off. Repeatedly pressing the button will change the functions of the
humidifier in the following order:
- First press
: indicator light "
LIGHT
" will flash three times, which indicates a change
in the mode. It is important to make the next press while the indicator light "
LIGHT
"
is flashing. Otherwise your desired change will not happen and the humidifier will
return to the mode used previously.
- Second press
: activate the sleep mode. The indicator light "
SLEEP
" will start
flashing 10 times and then turn off the backlight and all the indicator lights. In the
sleep mode, the fan speed is set to "
I
" (lowest speed).
It is important to make the next press while the indicator light "
SLEEP
" is flashing.
Otherwise your desired change will not happen and the humidifier will set itself to
sleep mode.
- Third press
: cancel the sleep mode. The humidifier will operate at speed "
I
" and the
backlight will be turned off.
- Fourth press
: turn on the backlight at the last set speed level. The indicator lights of
the set speed and the indicator light "
LIGHT
" will be lit.
Automatic mode
■
Press button
AUTO
B2
to activate the automatic mode. In this mode, the humidifier
will monitor and measure the ambient air humidity and adjust the fan speed
automatically to achieve the optimal air humidity relative to ambient air humidity.
- Humidity 0 – 45 RH %
: fan speed
III
and a red backlight
- Humidity 45 – 65 RH %
: fan speed
II
and a blue backlight
- Humidity > 65 RH %
: fan speed
I
and an orange backlight
■
To cancel the automatic mode, press button
AUTO
B2
.
Setting fan speed
■
Button
B3
serves to set the fan speed. Repeatedly pressing the button will
change the speed of the fan in the following order:
I
(lowest speed) –
II
(middle
speed) –
III
(high speed) –
TURBO
(highest speed, where all the speed indicator
lights are lit).
Low water level indicator
■
As soon as the water level falls below the set level, the indicator light "
ON/OFF
" will
start flashing red.
■
Add water if necessary. Prior to adding water, check that the humidifier is turned
off and that the power adapter
A12
is disconnected from the power socket. Then
you may continue according to the instructions in section "
Filling the water tank
".
■
When not using the humidifier, leave it turned on. The fan will remain in operation
even for several hours to ensure that the humidifying filter
A7
is dried out, and then
it will stop automatically.
■
The fan will remain in operation for 7 hours (normal mode) or 10 hours (sleep mode)
and the indicator light "
ON/OFF
" will flash red for the entire time.
CLEANING AND MAINTENANCE
■
Disconnect the adapter power plug from the power socket and allow the appliance
to cool down before cleaning it.
■
For cleaning, do not use cleaning products with an abrasive effect, solvents, etc. that
could damage the appliance. No part of this appliance is intended for washing in
a dishwasher.
Warning:
To prevent the risk of injury by electrical shock, do not submerge
the appliance, the adapter or its power cord in water or any
another liquid.
Regular cleaning
■
Regularly clean the appliance based on the amount of use. With standard use, clean
the humidifier once per week. The more frequently you use the humidifier, the more
frequently you will need to clean it.
1. Turn off the humidifier using button
B5
and disconnect the power adapter
A12
from the power socket.
2. Press the safety clip
A8
and carefully lift up the motor unit
A3
.
3. Wipe the motor unit with a soft sponge lightly dampened in warm water. Wipe it
with a dry wiping cloth.
4. Remove the humidifying filter
A7
with the attached limiter
A5
and float switch
A6
from the water tank
A10
.
5. Rinse out the water tank with clean warm water and wipe it dry.
6. If necessary, rinse the float switch under clean running water and wipe it dry.
6. Rinse the humidifying filter
A7
under clean running water. In the event of greater
soiling, you may soak it in clean water. The water temperature should not exceed
60 °C, otherwise there is a risk that the filter
A7
will change colour.
7. You can carefully squeeze the walls of the filter to remove any soils from the creases.
8. In the event that the filter
A7
is heavily soiled, you can add a small amount of
a vinegar or fine alkaline cleaning product. Then thoroughly rinse it under running
water.
However, the cleaning time should not exceed 8 minutes.
Note:
None of the cleaning methods described above will affect the absorption
characteristics of the humidifying filter
A7
. The filter
A7
can absorb a large
amount of water during the cleaning process, which reduces its strength.
After being cleaned and dried, its strength returns to more than 85 % of
the normal strength.
Removing limescale deposits
■
In the event that limescale deposits form in the water tank
A10
, use a 1:1 vinegar-
water solution or a solution of a vinegar-based cleaner with water at a ratio of 1:3.
■
Apply the solution using a sponge with which the inside of the water tank
A10
is
wiped out. In the event of heavier soiling, you can pour the solution into the water
tank
A10
and allow it to act for a while. Then thoroughly rinse it with warm water.
