- 4 -
Revision 03/2022
Copyright © 2022, Fast ČR, a.s.
• If you wish to stop releasing steam, release the steam button.
• We recommend to select
ECO
mode for all standard ironing tasks.
Only when ironing linen fabrics, strong silk or similar fabrics is it
recommended to select the
mode.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
IRONING WITH VERTICAL STEAM
•
The iron can also be used when ironing hanging textiles (e.g. curtains,
garments hanging on coat hangers, etc.).
•
Use the SET button to select mode
and wait until the indicator
remains permanently lit.
•
Position the iron into a vertical position. Use one hand to gently
tension the fabric and vertically move the iron from bottom up and
press the steam button to release steam.
Warning:
Never point the current of steam at persons or
animals.
Never attempt to remove creases from garments that
somebody is wearing.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
STEAM SURGE FUNCTION
•
When ironing particularly large creases, the steam boost function
can be used. Quickly pressing the steam button twice will activate
the function and the iron will release a strong steam boost for 2
seconds.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DETECTION OF ABSENCE OF WATER
•
In the event that the water level in the water tank declines below
the maximum water level during the ironing process, the indicator
will start flashing and the pump inside the base unit will
automatically shut off. This will prevent damaging the base unit
and extend the lifetime of the appliance. In such a case, disconnect
the base unit from the power socket and add water as described in
chapter FILLING THE WATER TANK.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DRIP-STOP SYSTEM
•
The iron is equipped with the Drip-Stop system, which automatically
stops water supply when the set temperature is insufficient for
generating steam and thereby prevents potential dripping of hot
water out of the steam outlets.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PUTTING THE IRON ASIDE WHILE IRONING
• During the ironing process, you can put the iron aside either on its rest
pad or on the rest pad of the base unit.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TIPS FOR QUALITY IRONING
• Follow the ironing instructions for each individual garment. Only iron
colourfast and heat resistant laundry. We recommend ironing laundry
with a print turned inside out.
• Never iron over places that have sweat marks or other stains. The high
temperature fixes the stain in place, making it difficult to remove.
• To avoid silk, wool and synthetic fabrics from being shiny after ironing,
iron them from the underside.
• Some materials are easier to iron when they are lightly damp.
• Spray fine fabrics before ironing them or iron them under a lightly
dampened wiping cloth. You can also hold the iron approx. 2 cm
above the laundry and use the ECO steam release mode.
• Iron very crumpled garments in the high steam mode.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
AUTOMATIC SHUT-OFF WHEN IDLE
• If you leave the iron idle for 10 minutes or do not press any button, the
iron will beep and shut itself off automatically. The indicator
will
light up on the display.
Warning:
Despite the iron being equipped with an automatic
shut-off function, for safety reasons, never leave it
without supervision when it is connected to a mains
power socket.
• In the event that the iron has automatically shut itself off, press the
SET button. The indicator
will start flashing and when it is lit, the
iron is again ready for use.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TURNING OFF
• Press and hold down main switch for at least 2 seconds. The iron will
shut off.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CLEANING AFTER USE
Warning:
Before cleaning, the base unit must be disconnected
from the power socket and the iron must have cooled
down.
When cleaning, do not submerge the iron or the power
cord of the base unit in water or any other liquid.
• Open the cap of the water tank filling hole and empty out any
remaining water over a sink. Close the cap.
• Wipe the dirty soleplate, the surface of the iron or the rest surface of
the base unit with a lightly dampened cloth and then wipe dry.
• For cleaning, do not use steel wool, solvents or cleaning products with
an abrasive effect, etc. to prevent damaging the surface being cleaned.
REMOVING LIMESCALE DEPOSITS
• For the removal of limescale deposits from the inner part of the
soleplate, the iron is equipped with a self cleaning function. When the
indicator starts flashing on the display, it is necessary to clean
the iron as soon as possible in the following procedure:
–
Fill the water tank with clean water up to the maximum water level
mark. Connect the base unit to a power socket and after releasing
the lock/release safety (if it was locked), take the iron off the base
unit.
–
Turn the iron on using the main switch and wait until the indicator
is lit on the display.
–
Hold the iron in a horizontal position above the sink. Hold down
the button for at least 3 seconds. Steam and hot water will start
to be released from the soleplate. At the same time also limescale
deposits from the inner parts of the soleplate will be removed. To
achieve better cleaning results, you can tilt the iron from side to
side several times.
–
When it beeps, the cleaning process if finished. Turn off the iron
using the main switch and place it on the rest pad, securing it in
place with the safety.
• Then disconnect the base unit from the power socket.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .