Masticating Slow Juicer
SSJ 4041BK / SSJ 4042RD / SSJ 4043WH
EN
EN-7
2015
04/2015
USING THE JUICER
1 . Make sure that the juicer is correctly assembled and then connect it to the el . power socket . The
juicer is equipped with a safety mechanism that prevents it from being started unless the lid is
correctly secured in the correct position .
2 . Place the juice jug A
8
, a glass or another suitable container below the juice spout A
7
. Open the
lock of the juice spout A
7
so that the juiced juice can flow freely out of the juice collector A
6
.
Place the pulp container A
0
below the pulp outlet A
9
.
3 . Prepare the fruit or vegetables . Thoroughly wash the ingredients and cut them up into pieces
that will pass through the feed tube A
2
. Remove hard stones that are contained in, for example,
apricots, peaches, mangoes, etc . and inedible peels, e .g . from oranges, pineapples, melons,
mandarins, etc .
4 . Prior to starting the juicer, make sure that the lid is properly secured in the correct position . To
turn on the juicer, turn the control dial A
qa
to the ON position . Take the pusher A
1
out of the
feed tube A
2
hole . Gradually add the prepared ingredients into the feed tube A
2
and push them
down using the pusher A
1
. You will achieve optimal results if you fill the feed tube A
2
gradually
pushing the ingredients down gently .
Attention:
Do not use fingers or other utensils to push ingredients through the feed tube A
2
. Always use
the pusher A
1
designed for this purpose .
The maximum time of non-stop operation of this appliance is 15 minutes . Then allow it to cool
down for 10 minutes .
5 . If the juice jug A
8
or pulp container A
0
fill up during the juicing process, turn the juicer off by
turning the control dial A
qa
to the OFF position, empty out the respective container and then put
it back in its place . Then you can put the juicer back into operation and continue juicing .
6 . When you have finished juicing, we recommend that you remove pulp remains from the juice
collector A
6
. Hold the control dial A
qa
in the "R" position (reverse motor rotation) for 3–5 seconds,
and then release it so that it returns to the OFF position . Repeat the entire process two to three
times . You can do the same in the event that you clog up the appliance with an excessive amount
of ingredients .
7 . Turn the juicer off by setting the control dial A
qa
to the OFF position and disconnect it from the
power socket . Prior to removing the juice jug A
8
, we recommended closing the spout A
7
so that
juice does not drip out of it .
8 . Disassemble the juicer, see chapter Disassembling the juicer and clean it out according to the
instructions contained in chapter Cleaning and maintenance .
DISASSEMBLING THE JUICER
1 . Before disassembling the juicer, make sure that it is turned off and disconnected from the power
socket . Make sure that all parts that move during operation have stopped moving .
2 . Close the juice spout A
7
and remove the juice jug A
8
and the pulp container A
0
. Take the pusher
A
1
out of the feed tube A
2
.
3 . Turn the feed tube A
2
anticlockwise until the open lock symbol shown on the lid A
2
is aligned
with the " " symbol on the juice collector A
6
and then take it off the juice collector A
6
.
4 . Remove the juice collector A
6
with the holder A
5
, strainer A
4
and auger A
3
inside off the base
A
qs
by turning it anticlockwise and lifting it up .
Note
:
It will be easier to take the juice collector A
6
off the base A
qs
when the pulp remains are cleaned
out after juicing, as described in point 6 in chapter Using the juicer .
5 . Take the auger A
3
, strainer A
4
and holder A
5
out of the juice collector A
6
.
