background image

10 

<Caution>

  Fresh Gas Calibration should be performed at the environment of fresh 

air without any influence of other gases, since the calibration is performed on the 

assumption that the concentration of Oxygen is 20.9%, that of Inflammable Gas is 

0%LEL, and the concentration of Toxic Gas is 0ppm in the fresh air.  Accordingly it 

is  not  recommended to  perform  Fresh  Air  Calibration  at  the  closed  space,  and  it 

should  be  avoided  to  perform  the  calibration  where  gases  can  be  inhaled  by 

operators. 

Save value 

Change value 

… 

Start 

calibration 

  If  Standard  Gas  Calibration  starts,  screen  of  detector  is  displayed  sequentially 

according to gas kind. That is, calibration proceeds for 60 seconds as information 

for 4 sensor appears once 1 second. If you want to cancel calibration, press arrow 

key.  Then  press  Power  key,  returns  in  Standard  Gas  Calibration  entry  ago. 

Concentration  of  Standard  Gas  Calibration  is  saved  by  state  that  change  only  in 

case calibration completes without problems. 

  If calibration is ended without problems, writing '

OK

' is appeared, and returns by 

Gas Measure Mode if press this after power key. 

Value 

60 second  

Count down 

ADC값 

Gas 

Value 

60 second  

Count down 

ADC값 

Gas 

… 

Summary of Contents for SP12C7






















Reviews: