Sentinel XL S-4000 User Instruction Manual Download

Page: 13 / 36

ECO: 102-0461-01

S-4014

Rev B

PREPARATION FOR USE (USING OR DECON WAIST BELT)
1.

Open the package/box and take out the components:

*If purchased as a system, HE filters, plug and battery are already installed into the

blower.

•

Sentinel XL™ HP Clear Hood Users Instruction Manual S-2012

•

Cartridges 2 each HE S-4002 or Optional S-4012 OV/CD/CL/HC/HF/SD/HE

Cartridges 3 each

•

Battery Charger (with Instructions) S-2009

•

Rechargeable Battery Pack S-2003 or Optional Non-Rechargeable Battery Pack

S-2004

*If purchased as a system battery is already installed into blower.

•

Alkaline Battery Adapter S-4013 (Optional)

•

Blower S-2002

•

Decon Quick Release Belt and Clip S-4011

•

Clear Hood S-3101

•

33” Long Breathing Hose S-4005 or Optional 25” Long Breathing Hose

•

Blower Plug S-4006 (with knob) or Optional S-4007 Flat Plug with installation /

Removal Tool

•

Flow meter S-2010

Remove Blower from box.

•

Usual packing method is for the battery pack, blower plug with knob, and HE

filters to be installed in the blower.

3. If using a rechargeable battery, remove the Battery Charger from its box. To

charge the PAPR:

•

Make sure that the battery pack is assembled to the blower unit at all times. The

battery pack should be separated from the blower only for battery pack

replacement.

•

Plug the battery charger to the socket at the back of the PAPR.

•

Connect the battery charger to an

electrical outlet. If charger is

connected to an electrical outlet

before connecting to a battery, a solid

green LED light indicates that the

charger is operating properly. When

plugged into the battery the charger

LED will turn solid red after a short

time, indicating that charging is

underway.

•

Charge the battery for approximately 5 hours.

•

The charger’s LED will change from solid red to flashing green when charging

is complete. The charger will then be in a “trickle charge” mode. If the light

goes to continuous green the battery is cooling down automatically and then will

go to red and continue charging.

Summary of Contents for XL S-4000





































Search results

Summary of Contents for XL S-4000

Reviews:

Related manuals for XL S-4000

Brands by name

Popular brands

Sentinel XL S-4000, User Instruction Manual

Search results

Summary of Contents for XL S-4000

Reviews:

Related manuals for XL S-4000

Brands by name

Popular brands