manualshive.com logo in svg

Sequoia Aircraft Corporation F.8L Falco, Construction Manual

The Sequoia Aircraft Corporation F.8L Falco Construction Manual is a comprehensive guide for building your own aircraft. This detailed manual provides step-by-step instructions and diagrams to help you successfully assemble your Falco. Download the free manual from 88.208.23.73:8080 and start constructing your dream airplane today.

Share
Download
background image

l

F.8L Falco Construction Manual

D–3

Revision 4, March 1, 2002

Notes

Cleaning of Equipment.  

Mixers, spreaders, etc., should be cleaned by washing with warm water.

The addition of isopropyl alcohol to the water will help to remove persistent residue.  Equipment
should be cleaned before the glue has time to set.

Note

Isopropyl alcohol and its vapours are highly inflammable.  Due precautions must be
taken against all possible fire risks.

Contact Between Hardener and Resin.  

Except where it is part of the prescribed gluing process,

contact between hardener and resin must be carefully avoided.  For example, if the applicator used
to spread the hardener is dipped into the resin solution container, the resin immediately starts to
thicken and set and become useless.

Avoidance of Iron Contamination.  

Care should be taken to avoid contact of resin or hardener

with nails, etc., or with ferrous fitments (for example, on brushes or containers), since this can
lead to staining on timber.  Staining is caused by the formation—under acid conditions—of iron-
tannin compounds (especially on woods with high tannin content, such as oak or ash).

Accidental discoloration—due, for example, to squeeze-out of the adhesive against a G-
clamp—may be removed by wiping the affected area with an absorbent pad moistened with 10%
citric acid solution.  Since this acid may itself cause colour changes in certain types of wood, it is
advisable first to test its effect on an off-cut.

Moisture Content of Wood.  

Wood that has been stored in an unheated shed or workshop may

be cold and contain excessive moisture; this may cause poor bonding.  It is therefore good practice
to store the wood in reasonably warm and dry conditions for several days before gluing.  For best
results the moisture content of the surfaces to be bonded should be within the range 7 to 13%.

Storage.  

Close the resin and hardener containers tightly when not in use and store in a cool

(ideally 5-20°C) dry place.  Shelf life under these conditions is at least two years for Aerolite 306
powder and at least three years for the hardeners.

Caution

Aerolite resins and hardeners are generally quite harmless provided that certain
precautions normally taken when handling chemicals are observed.  These
precautions amount simply to reasonable care and cleanliness.  Keep the uncured
materials (resins, hardeners, glue mixtures) away from foodstuffs.  Cover any skin
abrasions before starting work.  Avoid contact with the skin as far as possible
during work.  Where contact does occur, clean the skin with a cotton pad (or
similar absorbent material) moistened with water—ensure in particular that glue
mixture is cleaned off before it has time to harden.  At the end of each working
period, wash the hands thoroughly with soap and water.  Disposable paper towels
should be used to dry the skin.  Avoid inhaling powdered materials (certain resins
and hardeners are supplied as powders).  These precautions are described in greater
detail in Ciba-Geigy Sheet No. AD.2 

Handling Precautions for Formaldehyde-based

Products and Vinyl Emulsion Adhesives

 which is available on request and should be

referred to for fuller information.

The Aerolite GB Hardeners.

  These materials contain formic acid—a corrosive

chemical which is harmful if taken internally or allowed to come in contact with

Summary of Contents for F.8L Falco








































































































































































































































































































































































































































Reviews:

No comments

Related manuals for F.8L Falco

SOL paragliders Ellus 5 Manual preview
Ellus 5
Brand: SOL paragliders Pages: 42
Cessna 162 SKYLANE Pilot'S Operating Handbook And Flight Training Supplement preview
162 SKYLANE
Brand: Cessna Pages: 242
Topmodel 02011 Manual preview
02011
Brand: Topmodel Pages: 16
ITV PARAPENTES Jedi 2 Manual preview
Jedi 2
Brand: ITV PARAPENTES Pages: 24
Wipaire Wipline 2100 Service Manual And Instructions preview
Wipline 2100
Brand: Wipaire Pages: 70
SKY PARAGLIDERS ANTEA 2 User Manual preview
ANTEA 2
Brand: SKY PARAGLIDERS Pages: 44
SKY PARAGLIDERS ATIS L Manual preview
ATIS L
Brand: SKY PARAGLIDERS Pages: 40
Aerola Alatus-M Series Assembling And Dismantling Manual preview
Alatus-M Series
Brand: Aerola Pages: 36
Navion 1950 Deluxe Operation Manual preview
1950 Deluxe
Brand: Navion Pages: 94
Textron Aviation Cessna 525 Manual preview
Cessna 525
Brand: Textron Aviation Pages: 57
Schempp-Hirth Mini-Nimbus C Flight And Service Manual preview
Mini-Nimbus C
Brand: Schempp-Hirth Pages: 73
Schempp-Hirth Flugzeugbau Ventus-3T Sport Flight Manual preview
Ventus-3T Sport
Brand: Schempp-Hirth Flugzeugbau Pages: 177
Nova susi Manual preview
susi
Brand: Nova Pages: 28
Nova MENTOR 3 Manual preview
MENTOR 3
Brand: Nova Pages: 28
Nova SOMNIUM Series Manual preview
SOMNIUM Series
Brand: Nova Pages: 37
Nova prion 4 Manual preview
prion 4
Brand: Nova Pages: 39
Nova SPEEDMAX 2 Manual preview
SPEEDMAX 2
Brand: Nova Pages: 39
Nova PHILOU Operator'S Manual preview
PHILOU
Brand: Nova Pages: 44

Brands by name

Popular brands

Load more brands