10
SESAMO
DUALCORE
CARRIAGES INSTALLATION
DANGER: carefully check the weight of the leaves to ensure they are within the
maximum capacity of the automated system; in case of doubt, do not proceed beyond the
installation phase; if leaves with weights near to the capacity limits are installed, more
frequent maintenance intervals and periodical checks to assess the state of wear of the
components must be adopted; always replace parts that show even slight signs of wear.
Fix the carriages to the leaves in the positions shown in fig.5
The positions shown in fig.5 depict the leaf seen from the inspection side (cover) of the
automated system.
To fix the door, use M8 screws (fig. 9 part. with hexagonal head with appropriate flat and
notched washer.
NOTE: for leaves equipped with a 'break glass' emergency system or glass leaves equipped
with clamps, use the mounting positions shown in the manuals of the relative accessories.
DANGER: incorrect installation could compromise the correct functioning of the
automated system and present a risk.
Ensure that the anti-derailing wheels (fig.9 ref.E) are fully lowered. Lift the leaf and place the
wheels of the carriages delicately on the guide rail, taking care not to damage the parts by
dropping or banging them.
DOOR ADJUSTMENT
The leaves can be adjusted on three axes (x,y,z) according to the requirements of the
installation.
LATERAL ADJUSTMENT (Y) FIG.9 - FIG.10
loosen the screws F and slide the leaf along the Y axis to the position where it will operate
correctly.
Take care to align the carriages correctly and ensure they are parallel to the guide rail, as
shown in Fig.10. To check the correct alignment, ensure that the distances "E" measured
between the leaf and the carriage are the same for all the carriages on both the left and right
sides. To further check the alignment, move the leaves manually: they should slide with the
minimum of effort without any impediment or abnormal friction. When the leaves are in the
correct position, tighten the screws F progressively, alternating between different screws
until they are all fully tightened.
WARNING: turning the screws F when tightening can cause the carriage to go out of
alignment. To avoid this, tighten alternate between screws F and tighten progressively.
Summary of Contents for DUALCORE LH100
