13
SESAMO
DUALCORE
INSTALLATION OF THE ELECTRIC LOCK
(
OPTIONAL
)
WARNING: install only the bistable safety electric lock for RD100 automated system.
WARNING: for LH100/LH140 automated systems it is possible to install standard (fail
secure), reverse (fail safe) or bistable electric locks
H.
install the electric lock inside the automated system using the appropriate
fixing screws in the channel of the box as shown in fig. 16
I.
make sure that the matching part slide on the carriage part. P fig. 5 is
positioned in compliance with what is indicated in fig. 5 according to the types
of inputs provided
J.
bring the leaf/leaves to complete closure
K.
move the electric lock up to bringing the locking rod B fig.16a to about 2mm
from the matching part A fig.16a on the carriage and then tighten the fixing
nuts of the electric lock
L.
WARNING
: set parameter 13 according to the type of electric lock
installed - see
commissioning of the automated system paragraphs
INSTALLATION OF THE EMERGENCY RELEASE LEVER
If the electric lock has been installed, secure the emergency release cable by following the
instructions below (fig.17):
-
before proceeding with the assembly, make sure that spring D is correctly inserted
in pipette A
-
insert stop B at the end of the cable under bracket C and pass it through the
appropriate slot
-
secure spring D between bracket C and F
-
insert the threaded part E of pipette A of the appropriate compartment on bracket
F
-
completely screw nut G
position the sheath in such way as to reach the position where you want to install the
release lever. It can be fixed on the automated system’s head (fig. 19) or in an easily
accessible point of the window or wall. It is possible to position the sheath in the cable
compartment of the box using the cable fasteners provided (fig. 14).
DANGER: the sheath must be positioned so that it does not have small creases and is
properly fixed to the supports. If the path of the sheath is too complicated or the
attachment too slack, the function of the emergency release system can compromised and
constitute a safety risk.
Insert the nut supplied (part. B fig. 18) in the special seat obtained in the lever body (part. A
fig.18). Fix the release lever in its definitive position using the screws provided (part.C fig.18).
fig.18
Summary of Contents for DUALCORE LH100
