14
SESAMO
DUALCORE
With reference to fig. 17a, cut the sheath and cable A using the tip of the lever in the open
position as a measure for cutting. Pull out cable B by around 160mm pulling it from the stop
on the electric lock. Cut the sheath again at the definitive measurement using the tensioner
on the lever as a gauge. Extract the cable which should protrude by around 160 mm from the
sheath.
DANGER: ensure that while cutting the sheath, no obstructions or offcuts is created
that can compromise the sliding of the cable.
Refer to fig.18 and insert the sheath F and cable B in the tensioner E and screw the tensioner
into the hole on the lever. Insert the small barrel G equipped with grain bolts H ensuring
they do not obstruct the hole in the barrel. Insert the cable D into the hole of the small
barrel G. Close the lever and pull lightly on the cable to remove any play. Keeping the cable
taut, tighten the grain bolts H with an Allen wrench H. Check that the release handle works
correctly and that it has sufficient space to open and fully release the electric lock. If the
tension of the cable needs to be adjusted, do so via the tensioner of the lever or the nut of
the pipette on board the electric lock. At the end of the checks, cut the steel cable.
DANGER: carefully test the correct function of the release lever. Any errors could
prevent the release of the leaf in the event of a failure of the electric lock and constitute a
safety risk.
DANGER: the release mechanism must be checked periodically for loose fastenings,
dirt, wear, corrosion or other unexpected phenomena that could compromise the correct
function of the mechanism.
COVER FIXING
With reference to fig.15, fix the cover in the special seats of the heads using screws
A
.
As an alternative, it is possible to fix the cover from the bottom using the screws/inserts art.
PF25.60 (optional) as follows:
-
drill 2 holes
C
diameter 5.5mm under the cover at 6mm distance from the ends
-
fix the cover with 5x10 screws
B
by screwing them into the inserts to be positioned
inside the heads
Summary of Contents for DUALCORE LH100
