17
SESAMO
DUALCORE
H-
protection fuses of 1AT located at the switching power supply input;
I-
display with keys for adjusting operating parameters and selecting operating modes;
J-
main key: removable memory stick for internal programming data of the processor;
WARNING: carefully check the main key is fully inserted (ref.J) before starting the
electronic processor. Otherwise unpredictable product malfunctions may occur.
K-
terminal for sensors and accessories;
L-
90° connector of the electrical network power supply (230VAC);
M-
connection screws for the earth connection (fig.22 part. M).
Earthing system
Through the earth connection, the Dualcore processor offers an additional protection for the
aluminum case and metal parts connected to it. To ensure the earth connection is effective,
tighten screws M (fig.22) and the nut of bolt O (fig.22) so that the aluminum case is
electrically connected to earth pole L1 (fig.2X).
WARNING: check that screws M (fig.22) and bolt O (fig.22) are correctly tightened and check
the electrical continuity between the earth pole L1 (fig.22) and the surface of the automated
system crossbeam. If this is not the case, an important safety feature of the entire system
may be compromised, with a risk of electric shock or malfunctions in the product.
PROCESSOR
/
SENSORS COMPLIANT WITH
EN16005
WARNING: the P56001 control unit CANNOT WORK with photocells connected directly
to the terminal board. The direct connection and switching on of the ELECTRONIC BOARD
WILL LEAD TO IREVERSIBILE DAMAGE.
The use of photocells can ONLY be done with the purchase of the photocell kit and the
dedicated firmware.
Fig.4 shows the sensors that can be connected to the Dualcore processor:
A-
left opening safety sensor
B-
internal opening/safety sensor
C-
external opening/safety sensor
D-
right opening safety sensor
opening sensors B. and C. perform the following 3 functions:
1-
opening control: detects movement in M1 or M2 areas and controls door opening -
for RD100 version the internal sensor B must be exclusively in performance level d
2-
closing safety: detects obstacles in zone A1 or A2 and in case of obstruction stops
the doors from closing
3-
test: check that the closing safety (function 2) is working correctly and, if not,
prevents the leaves from closing (ref.EN16005 performance level C)
Summary of Contents for DUALCORE LH100
