–
Fit the kneading insert over the shaft
extension and push it firmly down as far as
it will go so that it almost touches the
bottom of the bowl.
–
Put the ingredients (max. 500g) into the
bowl.
–
Place the lid on the bowl and lock it by
turning clockwise until it clicks into place
in the handle.
–
For safety reasons, use the pestle at all times
when feeding the ingredients into the food
chute. During operation, the pestle should
remain inserted.
Short-term operation:
When using the kneading function, please
note that the appliance is designed for
short-term operation only, i.e. the unit must
not be operated for more than 2 minutes at
a time. Switch off the appliance afterwards
and allow sufficient time (around 5 mins)
for it to cool down before resuming
operation.
Operation settings
–
Start the kneading process at speed level
I
.
Once the dough has reached a firmer
consistency, continue kneading at speed
level
II
.
C. Whipping cream / beating egg-white
–
Fit the drive shaft into the drive clutch.
–
Fit the bowl to the motor housing with its
handle on the right and turn clockwise all
the way to engage the safety lock.
–
Place the drive shaft extension on the drive
shaft.
–
Fit the blender disc for whipped cream and
egg-white over the shaft extension and push
it firmly down as far as it will go so that it
almost touches the bottom of the bowl.
–
Put the ingredients (max. 400g) into the
bowl.
–
Place the lid on the bowl and lock it by
turning clockwise until it clicks into place
in the handle.
–
During operation, the pestle should always
remain inserted.
Short-term operation:
When whipping cream or beating egg-
white, please note that the appliance is
designed for short-term operation only, i.e.
the unit must not be operated for more than
2 minutes at a time. Switch off the appliance
after wards and allow sufficient time
(around 5 mins) for it to cool down before
resuming operation.
Operation settings
–
Start processing at speed level
I
and
increase to level
II
if necessary.
D. Slicing and shredding/grating
–
Fit the drive shaft into the drive clutch.
–
Fit the bowl to the motor housing with its
handle on the right and turn clockwise all
the way to engage the safety lock.
–
Hold the insert mounting with the grating
surface facing up.
–
First fit the edge of the selected insert into
the side of its mounting.
–
Now press the opposite side of the insert
into the mounting.
(To remove the insert, push it up from
below on this side until it comes free from
the mounting.)
–
When properly inserted, the upper surface
of the insert must be flush with the surface
of the disc.
–
Fit the insert mounting with the desired
insert onto the shaft extension.
–
Place the lid on the bowl and lock it by
turning clockwise until it clicks into place
in the handle.
–
For safety reasons, use the pestle at all times
when feeding the ingredients into the food
chute.
–
Always switch the appliance on before
feeding the ingredients into the food chute.
–
Do not put in more than 1 kg of food.
When processing larger quantities, the bowl
must be emptied from time to time.
Short-term operation:
When using the slicing and shredding or
grating
function, please note that the
appliance is designed for short-term
11
Summary of Contents for KM-3902
