background image

2

3

ENGLISH

ENGLISH

1.  INFORMATIONS

MANUFACTURER

 

SF Tech Sàrl 

 

Rte du Verney 18 

 

1070 Puidoux 

 Switzerland

 

Phone: +41 21 946 29 88 

 www.sftech.ch 
 info@sftech.ch

PICTOGRAMS

Warning

Read the manual

30

Machine wash at 30ºC

Do not bleach

Do not machine wash

Do not iron

Do not tumble dry

Do not dry clean

2.  WARNINGS

SAFETY INSTRUCTIONS

 

‹

Read this manual carefully and keep it for future reference.

 

‹

SF Tech heating system must be used in accordance with the manufacturer’s instructions and specifications.

 

‹

You should frequently pay attention to the skin under heated areas to avoid burns!

 

‹

Use only under a functional dry suit.

 

‹

Do not turn on the battery out of the water.

 

‹

Do not store or stack when the power is on.

 

‹

Use only with a disconnectable external battery with power adjustment.

 

‹

The maximum operating voltage must not exceed 12V.

 

‹

The system should not be used at the maximum setting when the battery is 100% charged. The first heating phase 
must be performed at a lower setting.

 

‹

Always start your activity with the power adjustment on the lowest setting.

 

‹

Switch off or disconnect immediately in case of malfunction or water leak inside the suit.

 

‹

Failure to follow the safety instructions can damage the equipment or cause serious injury.

 

‹

Inspect the entire system and cables before each use. Any type of damage, cut or breakage can result in serious 
injury.

THERMAL INSULATION

 

‹

Changes in ambient pressure can cause a variation of the properties of the insulating materials.

 

‹

Use underwear appropriate to the environmental conditions and type of activity performed.

 

‹

Inadequate insulation can lead to risks such as hypothermia or hyperthermia.

BATTERIE

 

‹

Only use batteries recommended by SF Tech.

 

‹

Refer to the manufacturer’s instruction manual.

LIMIT OF USE

 

‹

The SF Tech heating system is a comfort system, it is not designed to exceed the physiological limits of the diver.

 

‹

The maximum depth of use is determined by the training and qualification of the diver, and the limitations of the 
equipment including but not limited to the battery.

 

‹

Use only compressed air to inflate the dry suit. All other gases, such as oxygen enriched air (Nitrox), argon or 
helium enriched gases (Trimix) could cause health damage or equipment damage.

 

‹

The use of diving equipment by a non-qualified person may result in serious injury or death.

Summary of Contents for HEATING SYSTEM





















Reviews: