SFA SANIMARIN MAXLITE+, Installation Instructions Manual

17

USA/CDN

12

 GUARANTEE

2 years guarantee from date of purchase, 

subject to correct installation and correct use: 

disposal of toilet papers and fecal matter only. 

Guarantee is limited to replacement of product 

if approved by SFA as well as replacement of 

spare parts.  Any indemnity or claim of damages 

along with labor charges for removal or re-ins-

tallation will not be included.

Freight and packing costs, travel expenses 

are not included in the guarantee. It does not 

cover any normal deterioration of the material 

over time, any external deterioration or accident, 

incorrect disposal of sanitary products. Any mo-

dification without prior notice will not be under 

11

 WINTERING

In the event of a long period without use, rinse the 

bowl and carry out several flushing cycles with 

the fresh water and close through-hull valves.

13

 FAULT FINDING

In most cases, any inconsistencies in the operation of the unit will be minor and easy recti-

fied. Please refer to the chart below. If the problem cannot be easily remedied thanks to this 

chart, please call our SFA Service organisation or go to a SFA-approved technician.

FAULT OBSERVED

PROBABLE CAUSES

TROUBLESHOOTING

•  The motor does not work

•  No electricity supply

• Check the control switch

• Check the electrical connections

• Check the power source.

•  The motor works but there is no 

water inlet for flushing

•  The inlet pipe filter is clogged

•  The water inlet pipe is

pinched

•  The through-hull  valve is 

closed

•  The pump is unprimed

•  The water injection nozzle /

check valve is clogged

•  The switch is wrongly 

wired up

•  Clean the filter

•  Check the pipes

•  Check the through-hull  valve

•  Check the pump and the flexible 

blade turbine  

•  If necessary change the turbine

•  Check the water injection nozzle

•  Check the check valve

•  Check the connection of the 

cables.

•  The motor works but there is 

no outlet

•  The outlet is clogged

•  The outlet is too high

•  The through-hull  valve is 

closed

•  There is no water in the bowl

•  The switch is wrongly wired up

• Dismantle and clean the outlet

• Change the outlet 

• Check the pipe routing 

• Check the through-hull  valve

• Add water to the bowl

• Check the connection of the 

cables.

•   The motor runs with a rattling 

noise

• A hard foreign body has fallen 

into the bowl

• Cut the power supply to the 

motor.

• Close the through-hull  valves

• Remove the motor unit

• Use a hook to remove all

matter that could interfere with the 

rotation of the shredder

• Use a tool to rotate the turbine in

both directions until it turns

freely

• Reconnect the power supply to 

the motor. and press the «Pump 

out» key to check the operation of 

the appliance

• Re-open the through-hull  valves

• If the macerator is still jammed 

we advise you to contact our  

ervice department who will be able 

to advise you or direct you to one 

of our service stations nearest to 

your area.

DISCONNECT THE ELECTRICAL POWER SUPPLY, 

BEFORE ATTEMPTING ANY WORK ON THE UNIT.

guarantee. Fixing, modification, or replacement 

of parts without our agreement will not be gua-

ranted, and will invalidate it. Our liability is solely 

for the product itself.

Guarantee starts from date of purchase we may 

request a copy of the invoice to validate the pur-

chase date.

9

 ELECTRICAL 

CONNECTION

Advice for wiring up the Sanimarin :
The maximum recommended voltage drop is 

5% or 0.6V for a supply voltage of 12V, and 

1.2V for a supply voltage of 24V; 
In the event of prolonged absence of supply or 

long absence, cut off the water and electricity 

supplies to the .

Electricity consumption per second:

12V : 0.007 Ah

24V : 0.004 Ah

Current consumption / Fuses:

12V : 300 W  / 25 A

24V : 360 W / 15 A

Electric diameter wire:

12V (300 W)

1.5 mm²  / 0.006’’ = 1 m/ 39 3/8v max

2.5 mm² / 0.1’’ = 2 m/ 78 3/4’’ max

4 mm²/ 0.16’’ = 3 m/ 118 1/8’’ max

6 mm²/ 0.24’’ = 4,3 m/169 5/16’’ max
24V (360W)

1.5 mm²/ 0.006’’ = 3,5 m/ 137 13/16’’ max

2.5 mm²/ 0.1’’ = 6 m/ 234 1/43’’ max

4 mm²/ 0.16’’ = 9,5 m/ 374’’ max

6 mm²/ 0.24’’ = 14 m/ 551 3/16’’ max

10

 CLEANING / DESCALING

For cleaning, use normal sanitary products.

CAUTION:

• Do not use aggressive chemicals (such as 

acetone, pure bleach, etc.) that could da-

mage the material of the bowl.

• Use a suitable standard toilet brush; do 

not use scouring or abrasive pads.

Livret MAXLITE 2018.indd   17

09/04/2018   16:29