background image

Improper handling of lithium batteries can result in an explosion of the batteries and/or 
release of harmful substances.

Worn-out or defective batteries can compromise the function of this product.

KEEP OUT OF REACH OF CHILDREN

. Swallowing may lead to serious injury or death in 

as little as 2 hours due to chemical burns and potential perforation of the esophagus. 
Immediately see doctor.

Replace the RTC lithium battery before it is completely discharged. Replace the battery 
every 5 years even if the battery is still working properly. The lithium battery must be 
replaced only with an identical 

CR1025

 Lithium / Manganese Dioxide (Li/MnO2) battery.

Do not throw lithium batteries into fire, do not solder on the cell body, do not recharge, do 
not open, do not short-circuit, do not reverse polarity, do not heat above 100°C and protect 
from direct sunlight, moisture and condensation.

Dispose of used batteries according to local regulations and the battery manufacturer's 
instructions.

Before opening the case, disconnect all power sources, any connection to external 
devices, including USB cables, and disconnect the UPS external battery.

Use a non-conductive pin or small tool to help extract the battery from its holder. Insert the 
new battery with a gentle push. You don't need tools to insert the battery. The battery is 
held into place by a spring contact.

Be sure to insert the battery so that the positive (+) terminal of the battery is in contact with 
the outer body of the battery holder, and the negative (-) terminal is in contact with the 
contact pad of the circuit board.

Reversing the battery polarity may damage the product.

The real time clock will reset its time immediately when the RTC backup battery is 
disconnected.

Software installation

Refer to the software installation section of the Strato Pi or Iono Pi user guide for detailed 
software installation and troubleshooting instructions.

The display and touch sensor unit used in Strato Pi Touch Display is the original 7” touch 
display developed by the Raspberry Pi Foundation. Refer to the raspberrypi.org website 
for additional software installation instructions.

WARNING

NOTICE

12

User Guide

Summary of Contents for Iono Pi Touch


















Reviews: