SGM G-1 BEAM User Manual Download | Manualshive

Page: 24 / 32

background image

24

The SGM POI versions are designed for permanent outdoor installation and are IP66-rated (or higher). POI versions are designed for

use in maritime and offshore environments, as per the C5-M corrosion-resistance class.

Physical differences

The POI version differs from the standard version by having fixed-chassis power and DMX cables, and heavy-duty cable glands. The

display/control panel, True 1 power connector and XLR DMX connectors have been removed.
The head unit is not detachable from the base unit with quick locks.
See G-1 Beam (POI) parts identification on page 6 for location of the different parts.

Configuration

The G-1 Beam POI does not include a display, therefore it has to be configured through RDM (Remote Device Management). See

“RDM” on page 23 for more information.
In POI versions, the DMX address and DMX mode can only be set through RDM. When addressing through USB powered DMX /

RDM devices, ensure DMX link is terminated, and keep a short cable length as far as possible.
Regarding the DMX modes for POI, they are the same as the standard G-1 Beam. Visit www.sgmlight.com to see all DMX charts

available under the respective product, or upon request via support@sgmlight.com.

PLEASE NOTE!!
Remote Device Management (RDM) requires a correct DMX cabled installation and termination.
When setting addresses through RDM and using USB dongles, disable the USB selective suspend to ensure a proper

voltage on the DMX link. If any lag or trouble occurs when addressing, decrease the cable length range to <12 m. and only

address one fixture at a time.

SGM Addressing Tool

SGM provides a Windows software tool designed to allow the user to address and configure the fixtures through RDM. Changing the

settings is done in the exact same way as it is in the display.

This tool is available for download at www.sgmlight.com, and has to be used with the SGM USB 5-Pin-XLR Uploader cable (available

from your SGM dealer).

POI Permanent Outdoor Installation

Figure 24: SGM Addressing tool

«
...
22
23
24
25
26
...
»

Summary of Contents for G-1 BEAM

































Reviews:

No comments

Related manuals for G-1 BEAM

Brand: Makita Pages: 17

Brand: Makita Pages: 13

Brand: idiag Pages: 10

Brand: Bandit Pages: 136

Versaflo S Series

Brand: 3M Pages: 11

DBI Sala EXOFIT

Brand: 3M Pages: 32

Brand: 3M Pages: 8

Brand: Accurate Bio-Medical Technology Pages: 35

Brand: ACE INSTRUMENTS Pages: 2

Brand: ODA Pages: 103

Brand: KBT Pages: 12

ABS-Lock DH04 Series

Brand: ABS Pages: 4

Sportsound SSR-300

Brand: Daktronics Pages: 42

Brand: T-Rex Pages: 13

BOMAG BW 100 ADM-5

Brand: Fayat Pages: 216

Brand: B medical systems Pages: 28

Brand: G-Systems Pages: 60

Brand: G-Lab Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands