420 774 335 397 www.sharks-shop.cz Stránka 30
d) Keep in mind that the operator or user is responsible for accidents or hazards occurring to other
people or their property.
e) If the supply cord is damaged, it must be replaced by the manufacture or its service agent or a
similarly qualified person in order to avoid a hazard.
f) This appliance is not intended for use by persons (including children) with reduced physical,
sensory or mental capabilities, or lack of experience and knowledge, unless they have been given
supervision or instruction concerning use of the appliance by a person responsible for their safety.
g) Children should be supervised to ensure that they do not play with the appliance.
SPECIFIC SAFETY RULES
1.
Before use check the supply and extension cord for signs of damage or aging. If the cord
becomes damaged during use, disconnect the cord from the supply immediately.
2.
DO NOT TOUCH THE CORD BEFORE DISCONNECTING THE SUPPLY. Do not use the
appliance if the cord is damaged or worm.
3.
Read the instruction carefully .Be familiar with the controls and proper use of the equipment.
4.
Keep extension cord away from cutting elements.
5.
Wear protective glasses and goggles.
6.
Never allow children or people unfamiliar with the instructions to use the machine.
7.
Stop using the machine while people, especially children, or pets are nearby.
8.
Only use the machine in daylight or good artificial light.
9.
Before using the machine and after any impact, check for signs of wear or damage and repair as
necessary.
10. Never operate the machine with damaged guards or without the guard in place
11. Keep hands and feet always from the cutting means at all times especially when switching on the
motor.
12. Take care, against injury from any device fitted for trimming the filament line length.
13. Never fit metal cutting elements;
14. Never use replacement parts or accessories not provided or recommended by the manufacturer.
15. Disconnect the machine from the mains before checking, cleaning or working on the machine and
when it is not in use.
16. Inspect and maintain the trimmer regularly. Have the trimmer repaired only by an authorized
repairer.
17. Take care against injury from the blade fitted for trimming the filament line length. After extending
new cutter line, always return the trimmer to its normal operating position before switching on.
18. Always ensure that ventilation openings are kept clear of debris.
19. When not in use, store the trimmer out of the reach of children.
20. For additional protection, the installation of a residual current device (RCD) having a rated residual
operating current not exceeding 30 mA is advisable
21. This appliance is not intended for use by persons (including children) with reduced physical,
sensory or mental capabilities, or lack of experience and knowledge, unless they have been given
supervision or instruction concerning use of the appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not play with the appliance.
22. The nylon line will run on for a few seconds after the tool is switched off! Do not touch moving
hazardous parts before the machine is disconnected from the mains and the moving hazardous
parts have come to a complete stop.
23. The type of extension cords to be used shall not lighter than HO5VVF or HO5RNF.
24. Always wear substantial footwear and long trousers while operating the machine.
25. Always disconnect the machine from the power supply
-
Whenever the machine is left by the user
-
Before cleaning a blockage
-
Before checking, cleaning or working on the machine
-
After striking a foreign object to inspect the machine for damage
-
If the machine starts to vibrate abnormally, for immediately check
26. Never to operate the machine with defective guards or shields, or without safety devices, or if the
cord is damaged or worn.
27. Do not connect a damaged cord to the supply or touch a damaged cord before it is disconnected
from the supply for the reason that damaged cords can lead to contact with live parts.
28. Disconnect the supply immediately in the event of accident or breakdown.
29. Connect the machine only to a supply circuit protected by a residual current device with a tripping
current of not more than 30 mA
Summary of Contents for SH 250 W
