background image

Optional Settings

112

Setting 18: RETRANSMISSION INTERVAL

You can select the number of minutes the fax waits between each memory 

retransmission attempt. Enter 

 

 for 1 minute, 

 

 for 2 minutes, 

etc., up to a maximum of 15 minutes. If you do not want the fax to wait 

between attempts, enter 

 

.

Initial setting: 02

Setting 19: POWER SAVE MODE

To conserve power, you can have the laser printer heater in your fax machine 
turn off when not in use. When this is done, the heater will turn on 
automatically when you receive a document (there will be a slight delay before 
printing while the heater warms up) and turn off when printing is completed. 

Press 

 to turn on Power Save mode, or 

 to turn it off.

Initial setting: 1

Setting 20: ANTI-JUNK FAX

Press 

 to block reception from fax numbers entered in the Anti Junk Fax 

List. Press 

 to allow reception from all numbers.

Initial setting: 2

Setting 21: ALARM VOLUME

This sets the volume of the beep sound that alerts you to error conditions and 

informs you that operations have been completed. Press 

 for HIGH, 

 

for LOW, or 

 for OFF.

Initial setting: 2

Setting 22: DIAL MODE

This sets the dial mode. Press 

 if you are on a touch-tone line, or 

 if 

you are on a pulse dial (rotary) line.

Initial setting: 1

0

1

0

2

0

0

1

2

1

2

1

2

3

1

2

Summary of Contents for 4470 - FO B/W Laser





















































































































































Reviews: