background image

Distinctive Ring

105

5. Spe

c

ial

Functions

Distinctive Ring

Important:

To use distinctive ring, you must subscribe to a distinctive ring service from 
your local phone company.

Your fax machine may not be compatible with some distinctive ring services.

Distinctive ring is a service offered by some local telephone companies 
whereby they assign an additional second number to your regular single line. 
The second number rings differently from your normal number.

If you subscribe to a distinctive ring service, you can set the fax machine to 
automatically answer when your second number is called. This allows you to 
use the second number as an exclusive fax number.

To have your fax automatically answer when your second number is called, 
follow the steps below:

1

Press 

, and 

 .

2

Press  

and .

3

Press a number from 

 to 

 to select the ring pattern below that 

matches your second number’s ring pattern. Or, press 

 to have your 

fax automatically answer your normal telephone number. Press 

 to 

turn off the distinctive ring function.

In the U.S.A.:

  

RING PATTERN 1

Two short rings

  

RING PATTERN 2

One short, one long, and one short ring

  

RING PATTERN 3

Two short rings and one long ring

  

STANDARD RING

Your standard (normal) ring pattern

  

OFF SETTING

Turn distinctive ring off

MENU

4

2

8

1

3

4

5

1

2

3

4

5

Display:

4:OPTIONAL SETTING

ENTER 

#(01-34, , )

28: DISTINCTIVE RING
ENTER # (1-5) (5)

Summary of Contents for 4470 - FO B/W Laser





















































































































































Reviews: