AL-1651CS TEST COMMAND, TROUBLE CODES 10 - 1
[10] TEST COMMAND, TROUBLE CODES
1. Entering the test command mode
To enter the serviceman test command mode, press the keys as
follows:
[#] key
→
[*] key
→
[C] key
→
[*] key
To cancel the test command mode, press the [CA] key.
2. Key rule
3. List of test commands
[10KEY]:
Entry of MAIN CODE/SUB CODE
Selection of an item
Setup of an adjustment value in case of test commands for adjustment
[
←
/
→
]:
Selection of MAIN CODE/SUB CODE
Selection of an item
[ENTER/START]: Settlement
<In case of test commands for print>
[ENTER]:
Settlement (Without print)
[START]:
Settlement/Print
[C]:
(Interrupting operation check) Returns to the upper hierarchy.
[ENTER] After pressing:
Settles the item and returns to the upper hierarchy.
[ENTER] Before pressing: Without settling the item, returns to the upper hierarchy.
In case of test command of operation check, terminates the operations.
[CA]:
Exits from the test command mode.
For a test command of adjustment, the display returns to the initial display (00-00).
Main
code
Sub
code
Contents
1
01
Mirror scan (SCAN CHK)
02
Mirror home position sensor (MHPS) status display
(MHP-SENSOR)
06
Mirror scan aging (SCAN AGING)
2
01
Single Paper Feeder (SPF) aging (SPF AGING)
02
SPF sensor status display (SPF SENSOR)
03
SPF motor operation check (SPF MOTOR CHK)
06
RSPF resist clutch operation check (RSPF RES.CHK)
08
SPF paper feed solenoid operation check (SPF SPUS
CHK)
09
RSPF reverse solenoid operation check (RSPF SPFS
CHK)
10
RSPF paper exit gate solenoid operation check
(RSPF SGS CHK)
3
03
Shifter operation check (SHIFTER CHK)
5
01
Operation panel display check (LCD/LED CHK)
02
Fusing lamp, cooling fan operation check (HT LAMP
CHK)
03
Copy lamp ON check
(C-LAMP CHK)
6
01
Paper feed solenoid (CPFS1, CPFS2, MPFS)
operation check (PSOL CHK)
02
Resist roller solenoid (RRS) operation check (RES.R
SOL CHK)
7
01
Check of warm-up display and aging with JAM (W-
UP/AGING)
06
Interval aging (INTERVAL AGING)
08
Shift to copy with warm-up display (Shift to equivalent
to CA key) (W-UP C-MODE)
8
01
Developing bias output (DVLP BIAS SET.)
02
Main charger output (Grid HIGH) (MHV(H) SET.)
03
Main charger output (Grid LOW) (MHV(L) SET.)
06
Transfer charger output (THV SET.)
9
01
Duplex motor normal rotation check (DPLX ROT.)
02
Duplex motor reverse rotation check (DPLX
ROT.REV.)
10
00
Toner motor operation (TONER MOTOR)
14
00
Cancel of trouble other than U2 (TRBL CANC.)
16
00
U2 trouble cancel (U2 TRBL CANC.)
22
04
JAM total counter display (JAM TTL CNT)
05
Total counter display (TTL CNT)
08
SPF counter display (SPF CNT)
12
Drum counter display (DRUM CNT)
14
ROM version display (ROM VER.)
16
Duplex counter display (DPLX CNT)
17
Copy counter display (COPIES CNT)
18
Printer counter display (PRT.CNT)
19
Scanner mode counter display (S-MODE CNT)
21
Scanner counter display (SCAN CNT)
22
SPF JAM counter display (S JAM CNT)
24
01
JAM total counter clear (JAM TTL CLR.)
04
SPF counter clear (SPF CLR.)
05
Duplex counter clear (DPLX CLR.)
07
Drum counter clear (DRUM CLR.)
08
Copy counter clear (COPIES CLR.)
09
Printer counter clear (PRT.CLR.)
13
Scanner counter clear (SCAN CLR.)
14
SPF JAM total counter clear (S JAM TTL CLR.)
15
Scanner mode counter clear (S-MODE CLR.)
25
01
Main motor operation check (MAIN MOTOR CHK)
10
Polygon motor operation check (LSU CHK)
Main
code
Sub
code
Contents
