background image

14

LC-13E1U/UB/UW
LC-15E1U/UB/UW

ADJUSTING PROCEDURE OF EACH SECTION

The best adjustment is made before shipping. If any position deviation is found or after part replace is performed, adjust
as follows.

1. Preparation for Adjustments

(1)Use the exclusive-use AC adapter or stable DC power supply.

AC adapter: UADP-A009WJPZ
DC power supply: 12 ± 0.5V

2. Special mode setting procedure

(1)After initialization of E

2

PROM the mode is changed to the adjustment mode.

[Procedure]
Connect TP2001 and TP2002 to GND, and turn on the power.

[Description]

»

The initialization of microprocessor is as follows.

»

AV position, DAC data, G/A data, sound processor data, and video chroma data adjustment values are taken as
defaults.

(2)Adjustment mode

[Procedure]
Short-circuit TP2001 to GND, and turn on the power.
Or short-circuit TP2002 to GND, and turn on the power.
Or holding down the [TV/VIDEO] key and [MENU] key, turn on the main power, and simultaneously press the
(inspection process) [CH 

"

] key and [VOL– ] key to change the mode to the adjustment mode.

[Description]
The manual adjustment or adjustment through communication with the automatic machine is performed.

(3)Shipping setting mode

[Procedure]
Holding down the [TV/VIDEO] key and [MENU] key, turn on the main power, and simultaneously press the
(inspection process) [CH 

'

] key and [VOL+] key to change the mode to the shipping setting mode.

Note: Keep it in mind to turn off the power immediately. If any key-in is accidentally made, the setting will be

canceled.

[Description]
User adjustment and other values are taken as defaults.
If TV is indicated as SETTING COMPLETE, setting has been completed.

3. Cancel of special mode

Turn off the Digital unit power.

Summary of Contents for Aquos LC 13E1U



















































































Reviews: