39
Setting Timer Recording (Continued)
3
Press
\
/
|
to select “Ch”.
• When you press
'
, channels are displayed in forward
direction.
• When you press
"
, channels are displayed in backward
direction.
: SELECT O K : ENTER M : BACK E : EXIT
M e n u [ C a r d
M e n u [ C a r d T i m e r r e c ]
S e t u p
S e t u p
A d j u s t T i m e r R e c . s e t t i n g
D a t e S t a r t S t o p C h M o d e S e t
D a t e S t a r t S t o p C h M o d e S e t
1 3 /
0
5 T h u 1 9 : 4 5
~
2 1 : 4 5 1 S P O n
0 0
NOTE
• Programmes set for Child Lock or set to “On” in “Skip” are not
displayed.
Press
\
/
|
to select “Mode”, and press
'
/
"
to select
either “SP”, “LP”, “EP” or “FIT”.
: SELECT O K : ENTER M : BACK E : EXIT
M e n u [ C a r d
M e n u [ C a r d T i m e r r e c ]
S e t u p
S e t u p
A d j u s t T i m e r R e c . s e t t i n g
D a t e S t a r t S t o p C h M o d e S e t
D a t e S t a r t S t o p C h M o d e S e t
1 3 /
0
5 T h u 1 9 : 4 5
~
2 1 : 4 5 1 S P O n
0 0
NOTE
• The recording is performed within the times set. When there is no
remaining time on the card, the message “Remaining Time 0:00” is
displayed and the recording will be interrupted. In this case, use
another card or delete recorded files to make more space. (See
page 45 for deleting files)
• FIT refers to automatic recording while adjusting image quality
between SP and LP so that the recording is completed within the
specified time. It may not be possible to record using FIT depend-
ing on the remaining capacity of the card.
• Two recordings cannot be programmed simultaneously for FIT.
Press
\
/
|
to select “Set”, and press
'
/
"
to select
either “On”, “Off” or “CLR”.
: SELECT O K : ENTER M : BACK E : EXIT
M e n u [ C a r d
M e n u [ C a r d T i m e r r e c ]
S e t u p
S e t u p
A d j u s t T i m e r R e c . s e t t i n g
D a t e S t a r t S t o p C h M o d e S e t
D a t e S t a r t S t o p C h M o d e S e t
1 3 /
0
5 T h u 1 9 : 4 5
~
2 1 : 4 5 1 S P O n
0 0
Press
OK
to set the timer.
Press
END
to exit.
NOTE
•
Timer programming settings are cancelled when the duration
of the power outage exceeds the backup time. (See page 21.)
12
8
9
10
11
Checking the Programme List
You can check the current recording states in the list.
Perform steps
1
to
3
in
Timer Rec
to display the “Timer
rec” screen.
Press
\
/
|
to select “Programme list”, and press
OK
.
: SELECT O K : ENTER M : BACK E : EXIT
M e n u [ C a r d
M e n u [ C a r d T i m e r r e c ]
P r o g r a m m e l i s t
S e t u p P r o g r a m m e l i s t
S e t u p P r o g r a m m e l i s t
Press
'
/
"
to select the file you want to check, and
press
OK
.
: SELECT O K : ENTER M : BACK E : EXIT
M e n u [ C a r d T i m e r r e c ]
M e n u [ C a r d T i m e r r e c ]
P r o g r a m m e l i s t
P r o g r a m m e l i s t
1 3 /
0
5 T h u 1 9 : 4 5 ~ 2 1 : 4 5 1 S P O n
1 4 /
0
5 F r i 2 1 : ~ 2 2 : 1 5 E P O n
1 5 /
0
5 S a t 1 9 : ~ 2 1 : 1 5 S P O n
0 0
0 0
0 0
0
0
0
0
0 0
Press
END
to exit.
To change the programme
In the step
3
above, press
'
/
"
to select the programme to be
changed or clear, and press
OK
.
Press
\
/
|
to select the desired item, and adjust with
'
/
"
.
1
2
4
LC-20B5E_E_P38-40.p65
04.2.26, 4:40 PM
39
Summary of Contents for AQUOS LC-15B5E
Page 66: ...64 ...