16
9 pin D-sub/MINI-DIN
conversion cable
(optional: AN-A1RS)
RS-232C serial control cable
(cross type, commercially available)
Communication conditions
Set the RS-232C communications settings on the PC to match the
TV’s communications conditions.
The TV’s communications settings are as follows:
Baud rate:
9,600 bps
Data length:
8 bits
Parity bit:
None
Stop bit:
1 bit
Flow control:
None
Communication procedure
Send the control commands from the PC via the RS-232C connector.
The TV operates according to the received command and sends a
response message to the PC.
Do not send multiple commands at the same time. Wait until the PC
receives the OK response before sending the next command.
Command format
Eight ASCII codes
+
CR
C1 C2 C3 C4 P1 P2 P3 P4
Command 4-digits Parameter 4-digits Return code
Command 4-digits: Command. The text of four characters.
Parameter 4-digits: Parameter 0 – 9,
×
, blank, ?
Parameter
Input the parameter values, aligning left, and fill with
blank(s) for the remainder. (Be sure that four values
are input for the parameter.)
When the input parameter is not within an
adjustable range, “ERR” returns. (Refer to
“Response code format”.)
When “?” is input for some commands, the present
setting value responds.
Response code format
Normal response
Problem response (communication error or
incorrect command)
Commands
NOTE
If an underbar (_) appears in the parameter column, enter a space.
If an asterisk (*) appears, enter a value in the range indicated in
brackets under CONTROL CONTENTS.
•
•
RS-232C port specifications
PC Control of the TV
When a programm is set, the TV can be controlled from the
PC using the RS-232C terminal.
The input signal (PC/video) can be selected, the volume can
be adjusted and various other adjustments and settings can
be made, enabling automatic programmed playing.
Attach an RS-232C cable cross-type (commercially available)
to a 9 pin D-sub/MINI-DIN (optional: AN-A1RS) for the
connections.
NOTE
This operation system should be used by a person who is
accustomed to using PCs.
•
•
•
Appendix (continued)
0
0
5
5
1
0
0
–
3
0
0
0
0
9
0
?
?
?
?
?
O
K
Return code (0DH)
E
R
R
Return code (0DH)
CONTROL ITEM
COMMAND PARAMETER
CONTROL CONTENTS
POWER SETTING
P O W R 0 _ _ _ POWER OFF
INPUT SELECTION A I T G D _ _ _ _ INPUT SWITCHING (TOGGLE)
I T V D _ _ _ _ TV (CHANNEL FIXED)
I A V D 0 _ _ _ TV
I A V D 1 _ _ _ EXT1
I A V D 2 _ _ _ EXT2
I A V D 3 _ _ _ EXT3
I A V D 4 _ _ _ PC
I A V D ? ? ? ? 0 to 4
CHANNEL
D C C H * * _ _ TV DIRECT CHANNEL (0 ~ 99)
D C C H ? ? ? ? 0 to 99
C H U P _ _ _ _ CHANNEL UP
C H D W _ _ _ _ CHANNEL DOWN
INPUT SELECTION B I N P 1 3 _ _ _ EXT1 (CVBS)
I N P 1 4 _ _ _ EXT1 (RGB)
I N P 1 ? ? ? ? 1 to 2
I N P 2 2 _ _ _ EXT2 (Y/C)
I N P 2 3 _ _ _ EXT2 (CVBS)
I N P 2 ? ? ? ? 0 to 1
I N P 3 0 _ _ _ EXT3
AV MODE
SELECTION
A V M D 0 _ _ _ AV MODE SELECTION (TOGGLE)
A V M D 1 _ _ _ STANDARD
A V M D 2 _ _ _ SOFT
A V M D 3 _ _ _ ECO
A V M D 4 _ _ _ USER
A V M D 5 _ _ _ DYNAMIC
A V M D ? ? ? ? 1 to 5
VOLUME
V O L M * * _ _ VOLUME (0 - 50)
V O L M ? ? ? ? 0 to 50
POSITION
H P O S * * * _ H-POSITION PC (-30 to +30)
H P O S ? ? ? ? PC (-30 to +30)
V P O S * * * _ V-POSITION PC (-10 to +10)
V P O S ? ? ? ? PC (-10 to +10)
C L C K * * * _ CLOCK (0 to 180)
C L C K ? ? ? ? 0 to 180
P H S E * * * _ PHASE (0 to 40)
P H S E ? ? ? ? 0 to 40
WIDE MODE
W I D E 0 _ _ _ WIDE MODE (Toggle)
W I D E 1 _ _ _ 4:3
W I D E 2 _ _ _ 16:9
W I D E ? ? ? ? 1 to 2
MUTE
M U T E 0 _ _ _ MUTE (Toggle)
M U T E 1 _ _ _ MUTE ON
M U T E 2 _ _ _ MUTE OFF
M U T E ? ? ? ? 1 to 2
SOUND WIDE
A C D V 0 _ _ _ SOUND WIDE (Toggle)
A C D V 1 _ _ _ SOUND WIDE ON
A C D V 2 _ _ _ SOUND WIDE OFF
A C D V ? ? ? ? 1 to 2
AUDIO CHANGE
A C H A _ _ _ _ SOUND SELECT (ST/Bilingual/mono)
SLEEP TIMER
O F T M 0 _ _ _ OFF
O F T M 1 _ _ _ 30 min
O F T M 2 _ _ _ 60 min
O F T M 3 _ _ _ 90 min
O F T M 4 _ _ _ 120 min
O F T M ? ? ? ? 0 to 120
