ADJUSTMENT
1 - 20
05 MODE
CODE
ADJUSMENT
MODE
DEFAULT RANGE
DESCRIPTION
PROCEDURE
GROUP
471
Paper remaining indicator. LCF manual
All
4
0-31
1
adjustment for LESS than 1/2 the capacity.
Key in the value, press the START key to store
or the CLEAR key to reset.
472
Paper remaining indicator. PFP upper manual
All
10
0-31
adjustment for LESS than 1/2 the capacity.
Key in the value, press the START key to
store or the CLEAR key to reset.
473
Paper remaining indicator. PFP middle
All
10
0-31
manual adjustment for LESS than 1/2 the
capacity. Key in the value, press the START
key to store or the CLEAR key to reset.
474
Paper remaining indicator. PFP lower manual
All
10
0-31
adjustment for LESS than 1/2 the capacity.
Key in the value, press the START key to
store or the CLEAR key to reset.
475
Paper remaining indicator. Automatic
All
—
—
8
adjustment for FULL condition. LCF and
PFP.
476
Paper remaining indicator. LCF manual
All
2
0-31
1
adjustment for MORE than 1/2 the capacity.
477
Paper remaining indicator. PFP upper manual
All
2
0-31
adjustment for MORE than 1/2 the capacity.
478
Paper remaining indicator. PFP middle manual
All
LT
0-31
adjustment for MORE than 1/2 the capacity.
size: 4
A/B
size: 8
479
Paper remaining indicator. PFP lower manual
All
LT
0-31
adjustment for MORE than 1/2 the capacity.
size: 7
A/B
size: 3
481
Drum motor speed fine adjustment.
Copier
128
0-255
1
482
Drum motor speed fine adjustment.
Printer
120
0-255
483
Registration motor speed fine adjustment.
Copier
128
0-255
1
484
Registration motor speed fine adjustment.
Printer
128
0-255
485
Fuser drive motor speed fine adjustment.
Copier
128
0-255
1
486
Fuser drive motor speed fine adjustment.
Printer
128
0-255
487
Transfer belt drive motor speed fine adjustment.
Copier
128
0-255
1
488
Transfer belt drive motor speed fine adjustment.
Printer
132
0-255
489
Pedestal drive motor speed fine adjustment.
Copier
128
0-255
1
490
Pedestal drive motor speed fine adjustment.
Printer
128
0-255
Perform the manual adjust-
ment when the remaining
amount of paper is less than
1/2. Perform adjustment code
470 first. Then adjust as
necessary.
Decrease the value in these
codes when the remaining
amount of paper indication is
slower than the actual amount
of paper.
Example: When the paper
remaining
indicator shows "
"
then changes suddenly to "
"
Load 4,000 sheets of paper in
the LCC and 500 sheets in the
Drawers, then perform the
automatic adjustment.
Perform the manual adjust-
ment when the remaining
amount of paper is greater
than 1/2. Perform adjustment
code 475 first. Then adjust as
necessary.
Increase the value in these
codes when the remaining
amount of paper indication is
greater than the actual amount
of paper.
Example: When the paper
remaining
indicator shows "
"
then changes suddenly to "
"
Increasing the value by 1
increases the motor speed by
0.067%. Set value to 128 for
the copier and 120 for the
printer.
Increasing the value by 1
increases the motor speed by
0.097%. Set value to 128 for
the copier and printer.
Increasing the value by 1
increases the motor speed by
0.061%. Set value to 128 for
the copier and printer.
Increasing the value by 1
increases the motor speed by
0.127%/step (or 0.254mm/
step). Refer to the complete
adjustment procedure before
performing this adjustment.
Increasing the value by 1
increases the motor speed by
0.061%. Set value to 128 for
the copier and printer.
Summary of Contents for AR-650
