background image

·

For two tray type

·

For one tray type

7. Attach the rear covers of the copier and the optional

paper feed unit.

Attach the rear covers of the copier and the optional paper feed unit
using two screws respectively.

8. Remove the securing fixture for packing the paper

feed unit and remove the packing material.

Remove the securing fixture for packing that fixes the paper pressure
plate of the tray by rotating it in the direction of the arrow and remove
the packing material.

9. Change the paper size in the tray.

Hold the grip and slide the cassette side plate to adjust it to the paper
to be used.

Then, fit the rear end plate to the specified size position.

Insert the power plug of the copier to the outlet and turn on the main
switch of the copier. Then, carry out the following procedure.

10. Load paper into the paper tray.

Do not exceed the maximum height line.

11. Check for center displacement.

·

Set an original on the document glass and copy it using the paper
tray in the copier.
Then, copy an original using the attached optional paper feed unit.

·

If the center of the copy image from the tray in the copier is differ-
ent from that of the copy image from the optional paper feed unit,
carry out adjustment referring to the service manual.

Installation of Paper feed unit is now complete.

Cassette relay harness

Relay harness for
dehumidification heater

Cassette relay harness

Relay harness for
dehumidification heater

Rear cover

Rear cover

Screws

Screws

Securing fixture for packing

[Caution]
Be sure to remove the 
securing fixture before 
turning on the power.

Packing material

Rear plate

Side plate

Summary of Contents for AR-D11




















Reviews: