background image

1

F o r   S h a r p   C a r o u s e l

®

 

B u i l t - i n   K i t

M o d e l s   R K - 4 2 S 2 4 ,   R K - 5 1 S 2 7 ,
R K - 5 1 K 3 0 ,   R K - 5 1 S 3 0   o r   R K - 5 1 W 3 0 .

THIS KIT IS UL APPROVED TO ALLOW CERTAIN MICROWAVE OVENS
TO BE INSTALLED ABOVE CERTAIN CONVENTIONAL/CONVECTION
WALL OVENS. PLEASE SEE THE OPERATION MANUAL REGARDING
APPROVED BUILT-IN APPLICATIONS.

I N S T A L L A T I O N   I N S T R U C T I O N S

3

®

1

2

4

5

6

7

NO.

PART NAME

  QTY

PART CODE

1

FRAME ASSEMBLY

1

S24

- FDECAB015MRY0

S27

- FDECAB008MRY0

S30

- FDECAB018MRY0

K30

- FDECAB019MRY0

W30 - FDECAB020MRY0

2

EXHAUST DUCT ASSEMBLY

1

S24

- FDUC-B019MRK0

S27

- FDUC-B032MRK0

S30

- FDUC-B032MRK0

K30

- FDUC-B032MRK0

W30 - FDUC-B032MRK0

3

POWER SUPPLY CORD

1

BOX ASSEMBLY
FCOVHB004MRK0

4

REAR DUCT

1

PDUC-B072MRP0

5

SCREW A

3

XCTSD40P10000

6

SCREW B

2

XTTSD40P30000

7

SCREW C

4

S24

- LX-CZB012MRE0

S27

- LX-CZB012MRE0

S30

- LX-CZB012MRE0

K30

- LX-CZB014MRE0

W30 - LX-CZB015MRE0

 IMPORTANT :

This Built-in Kit is designed for and approved only for those Sharp
Microwave Ovens specifying Built-In Kit RK-42S24, RK-51S27, RK-51K30,
RK-51S30 or RK-51W30 on the rating label on the left side wall of the
oven cavity.

The cabinet or wall opening must be within the following dimensions:

RK-42S24

HEIGHT

: 15 

11

/

16

" to 16"

WIDTH

: 22 

1

/

16

" to 22 

3

/

8

"

DEPTH

: minimum 19 

1

/

4

"

*RK-51S27, *RK-51K30,

HEIGHT

: 16 

3

/

4

" to 17"

*RK-51S30 & *RK-51W30

WIDTH

: 24 

3

/

8

" to 24 

11

/

16

"

DEPTH

: minimum 20"

* IF YOUR LOWER CONVENTIONAL OVEN IS NOT LISTED IN THE OPERATION MANUAL OF

THE MICROWAVE OVEN AS AN APPROVED MAKE AND MODEL, THEN DO NOT INSTALL
THE MICROWAVE OVEN ABOVE IT OR IN ANY AREA WHERE HEAT AND STEAM ARE
GENERATED; FOR EXAMPLE, NEXT TO OR ABOVE A CONVENTIONAL RANGE.
S= Stainless, K=Black, W=White

PLEASE READ THESE INSTRUCTIONS THOROUGHLY BEFORE
BEGINNING INSTALLATION!

Be sure to DISCONNECT THE PLUG of the microwave oven from the
electrical outlet before installing the Built-in Kit. Remove the  Carousel
turntable from the oven cavity.

Because the kit includes metal parts, due caution should be used in
handling and installation to avoid the possibility of injury.

Summary of Contents for Carousel RK-42S24

Page 1: ...oved only for those Sharp Microwave Ovens specifying Built In Kit RK 42S24 RK 51S27 RK 51K30 RK 51S30 or RK 51W30 on the rating label on the left side wall of the oven cavity The cabinet or wall opening must be within the following dimensions RK 42S24 HEIGHT 15 11 16 to 16 WIDTH 22 1 16 to 22 3 8 DEPTH minimum 19 1 4 RK 51S27 RK 51K30 HEIGHT 16 3 4 to 17 RK 51S30 RK 51W30 WIDTH 24 3 8 to 24 11 16 ...

Page 2: ...P 1 CABINET OR WALL OPENING SCREW B SCREW B EXHAUST DUCT ASSEMBLY The opening in the wall or cabinet must be within the following dimensions Outlet should NOT be in the shaded area as indicated on Sketch 1 NOTE 1 If the dimension of DEPTH C is more than 21 the outlet location may be any area on the rear wall NOTE 2 The floor of the opening should be constructed of plywood strong enough to support ...

Page 3: ...ecure the right flange of the REAR DUCT with SCREW A See Sketch 3 3 Plug the oven power supply cord into the POWER SUPPLY CORD BOX ASSEMBLY receptacle See Sketch 4 4 Slide the POWER SUPPLY CORD BOX ASSEMBLY into the REAR DUCT and secure the POWER SUPPLY CORD BOX ASSEMBLY and REAR DUCT with two SCREWS A See Sketch 5 SCREW A Sketch 3 REAR DUCT POWER SUPPLY CORD BOX ASSEMBLY Sketch 4 Sketch 5 REAR DU...

Page 4: ...tch 7 3 Position the FRAME ASSEMBLY to be square with the oven Carefully place the FRAME ASSEMBLY on the oven Check that it is level and then secure with two SCREWS C See Sketch 8 4 Secure the bottom portion of the FRAME ASSEMBLY with the two remaining SCREWS C See Sketch 8 SHARP ELECTRONICS CORPORATION Sharp Plaza Mahwah New Jersey 07430 2135 TINSEB279MRR0 Printed in U S A Sketch 6 FOOT POWER SUP...

Reviews: