<P=004>
RECORDING
●
When recording important selections, be sure to
make a preliminary test to ensure that the desired
material is being properly recorded.
●
The VOLUME, X-BASS and EQUALIZER controls
may be adjusted with no effect on the recorded sig-
nal (Variable Sound Monitor).
●
Metal and CrO
2
tapes should not be used for recording or
dubbing.
■
Recording from the built-in CD player
(CD Synchronized Recording System)
1
Press the ON/STAND-BY button to turn the power on.
2
Press the CD button and load the desired disc.
●
Use the APMS function to store the tracks you want to record
in memory. (See page 10.)
3
Load a cassette into the TAPE 2 cassette compartment.
4
Press the REC PAUSE (
●
6
) button.
●
"SYNC" and "REC" will flash.
5
Press the
0 /R
(TAPE 2
0
) button.
●
"SYNC" will disappear and "REC" will light up.
●
CD playback will start approximately 5 seconds after the tape
starts.
To stop recording:
Press the
■
(CD
■
) button.
The CD and tape will stop.
Note:
●
When the end of the tape is reached while recording, the CD
player will display the track number which was being played
at that time, and stop automatically.
TAPE
CD
TAPE 2
TUNER
(BAND)
ON/
STAND-BY
CD
TAPE (1 2)
REC PAUSE
CD
TUNER
(BAND)
TAPE
(1 2)
POWER
ON/
STAND-BY
TAPE 1 TAPE 2
If you want to restart recording from the beginning of the in-
terrupted track, turn over the tape, press the REC PAUSE
(
●
6
) button and then the
0/R
(TAPE 2
0
) button.
(If tracks have been stored in memory using the APMS func-
tion, recording will restart from the first track stored in
memory.)
■
Dubbing from tape to tape
1
Press the ON/STAND-BY button to turn the power on.
2
Load a prerecorded cassette into the TAPE 1 cassette com-
partment. Insert a blank tape into the TAPE 2 cassette com-
partment.
●
It is recommended that the recording tape be the same length
as the master tape.
3
Press the TAPE (1
V
2) button until "TAPE 1" appears in the
display.
4
Press the REC PAUSE (
●
6
) button.
5
Press the
0 / R
(TAPE 2
0
) button.
To stop dubbing:
Press the
■
(TAPE
■
) button.
●
TAPE 1 and TAPE 2 will simultaneously stop.
■
Erasing recorded tapes
●
Make sure that TAPE 1 is not in use.
1
Load the tape to be erased into the TAPE 2 cassette com-
partment.
2
Press the TAPE (1
V
2) button until "TAPE 2" appears in the
display.
3
Press the REC PAUSE(
●
6
) button.
4
Press the
0 / R
(TAPE 2
0
) button.
■
Recording from the built-in radio
1
Tune in to the desired station. (See pages 11-12.)
2
Load a cassette into the TAPE 2 cassette compart-
ment.
3
Press the REC PAUSE (
●
6
) button.
●
"REC" will flash.
4
Press the
0 / R
(TAPE 2
0
) button.
●
"REC" will appear.
Note:
●
If a whistling noise is heard while recording from an
AM station, move the AM loop antenna to a position
where noise is no longer heard from the unit.
To stop recording:
Press the
■
(TAPE
■
) button.
CD-BA120(SEC) TINSE0299AWZZ
13
