Sharp CD-XP700H, Service Manual

– 11 –

CD-XP700H

Figure 11-2

CD ERROR CODE DESCRIPTION

Error

Explanation

01

When Pickup set inner position, inner switch
cannot detect 'ON' level for 10 secs.

When tray moves to Open/Close, Open/Close switch

10*

cannot detect 'ON' level for 7 secs.
When disc table rotate to target position.
Clamp switch cannot detect 'ON' level for 7 secs.

When disc table set to Disc1 position for 1 st time,

11*

"CLAMP SW", "DISC NO SW" and "OPEN/CLOSE"
cannot detect 'ON' level for 14 secs.

31

When it changes to CD function, DSP cannot read
initial data.

T

T

EFBL

FDO

TE

Stopped

CH1=500 mV

DC   10:1

CH2=200 mV

DC   10:1

CH3=1 V

DC   10:1

500 ms/div

(500 ms/div)

NORM:20 kS/s

1

2

3

=Record Length=

Smoothing :   ON

CH1  :      0.000 V
CH2  :      0.000 V

Main  :     100K
Zoom  :       2k

Mode  :   SINGLE
Type   :   EDGE CH1
Delay  :                    0.0 ns
Hold off  :                0.2 

µ

s

CH3  :        0.00 V
CH4  :        0.00 V

BW   : FULL

=Trigger=

=Filter=

=Offset=

CH2
  v/DIV
   200 mV

1999/04/05  20:26:47

CD SECTION

Figure 11-1 ADJUSTMENT POINTS

Items adjusted automatically

(1) Offset adjustment (The offset voltage between the head

amplifier output and the VREF reference voltage is
compensated inside the IC.)

  * Focus offset adjustment
  * Tracking offset adjustment

(2) Tracking balance adjustment (waveform drawing

Fig.11-2 EFBL)

(3) Gain adjustment (The gain is compensated inside the IC

so that the loop gain at the gain crossover frequency will
be 0 dB.)

  * Focus gain adjustment
  * Tracking gain adjustment

•  Adjustment

Since this CD system incorporates the following automatic
adjustment functions, readjustment is not needed when
replacing the pickup. Therefore, different PWBs and pickups
can be combined freely.
Each time a disc is changed, these adjustments are
performed automatically. Therefore, playback of each disc
can be performed under optimum conditions.

* 'CHECKING'
If Error is detected, 'CHECKING' will be display instead of 'ER-
CD**' display. 'ER-CD**' display will only be display when
error had been detected for the 5 th times.

Test Stage

Frequency

Frequency

Display

Setting/

Adjusting

Parts

Instrument

Connection

• 

 AM IF/RF

Signal generator: 400 Hz, 30%, AM modulated

*1. Input: Antenna

Output: TP302

*2. Input: Antenna

Output: TP301

TUNER SECTION

fL: Low-range frequency
fH: High-range frequency

AM IF

450 kHz

1,620 kHz

T351

*1

AM Band

—

522 kHz

(fL): T306

*2

Coverage

1.1 

±

 0.1 V

AM Tracking 990 kHz

990 kHz

(fL): T303

*1

AM IF

TP301

TP302

R381

R357

T303

T306

L354

T351

CNP301
AM LOOP
ANTENNA

AM BAND
COVERAGE fL

AM TRACKING
fL

MAIN PWB

FE301

SO301
FM ANTENNA
TERMINAL

•  FM IF
Notes:
1: Description of the "FM IF Adjustment" is not carried on this

Manual. It is because the IF coil in the FM front end section
has been best adjusted in the factory so that its further
adjustment is not needed at the field. When replacing the
FM front end assembly, no adjustment is needed either.

2: The parts in the FM front end section are prepared in a

complete unit, so you can't obtain each part individually.